intersil Manuals (Industrial)

The HC5549 is a low power SLIC for use in short loop ISDN, PABX and Pairgain applications.

File format: PDF Size:267 KB

The HC5526 is a subscriber line interface circuit that is compliant with CCITT standards. Enhancements include immunity to circuit latch-up during hot plug and absence of false signaling in the presence of longitudinal currents. The HC5526 is fabricated in a High Voltage Dielectrically Isolated (DI) Bipolar Process that eliminates leakage currents and device latch-up problems normally associated with Junction Isolated (JI) ICs. The elimination of the leakage currents results in improved circuit performance for wide temperature extremes. The latch free benefit of the DI process guarantees operation under adverse transient conditions. This process feature makes the HC5526 ideally suited for use in harsh outdoor environments.

File format: PDF Size:354 KB

HC5523 LSSGR/TR57 CO/Loop Carrier SLIC with Low Power Standby is interchangeable with Ericsson's PBL3764A/4 for distributed central office applications. The product has good hot-plug resistance and can resist false triggering in the presence of long currents. HC5523 is fabricated in a High Voltage Dielectrically Isolated (DI) Bipolar Process that eliminates leakage currents and device latch-up problems normally associated with junction isolated ICs. The elimination of the leakage currents results in improved circuit performance for wide temperature extremes. The latch free benefit of the DI process guarantees operation under adverse transient conditions. This process feature makes the HC5523 ideally suited for use in harsh outdoor environments.

File format: PDF Size:510 KB

This product is a subscriber line interface circuit which is interchangeable with Ericsson PBL3860 for distributed central office applications.

File format: PDF Size:401 KB

The UniSLIC14 family is a family of Ultra Low Power SLICs from Intersil. It features automatic single and dual battery selection and battery tracking anti clipping to ensure the maximum loop coverage on the lowest battery voltage. It is ideal for power critical applications such as ISDN NT1+, Pairgain and Wireless local loop products.

File format: PDF Size:695 KB

The HC5503PRC is a low-cost SLIC optimized for large Telecom switches. It combines a flexible voltage feed architecture with the Intersil latch-free DI bonded wafer process, to provide a low component count, carrier class solution at very low cost. The re-configurable design permits simple, economical solutions for campus-wide call center and PBX applications. External components can be used in conjunction with the high battery voltage capability to meet the complex impedance and long loop drive requirements of Central Office switches, worldwide.

File format: PDF Size:217 KB

ISL35822 is an Octal 2.488Gbps to 3.187Gbps/ Lane Retimer from Intersil, supporting speeds from 2.488Gbps to 3.187Gbps, with a working voltage of 1.5V and a 192-pin EBGA-B package.

File format: PDF Size:1041 KB

The BBT3821 Octal 2.488Gbps to 3.187Gbps/ Lane Retimer supports 8 lanes of clock & data recovery and retiming with ultra low power consumption of only 195mW per lane.

File format: PDF Size:1040 KB

BBT3420 is a quad 2.488-3.1875Gbps/channel transceiver that supports full rate and half rate, with a maximum data rate of 12.75Gbps.

File format: PDF Size:773 KB

The EL1516 is a dual, ultra low noise amplifier, ideally suited to line receiving applications in ADSL, VDSL, and home PNA designs.

File format: PDF Size:343 KB

The EL2227 is a dual, low-noise amplifier from Intersil, ideally suited to line receiving applications in ADSL and HDSLII designs. The product has a low noise specification of just 1.9nV/√Hz and 1.2pA/√Hz, making it ideal for the detection of very low amplitude signals. The EL2227 features a -3dB bandwidth of 115MHz and is gain-of-2 stable. The product also affords minimal power dissipation with a supply current of just 4.8mA per amplifier. The amplifier can be powered from supplies ranging from ±2.5V to ±12V. The EL2227 is available in a space-saving 8 Ld MSOP package as well as the industry-standard 8 Ld SOIC. It can operate over the -40°C to +85°C temperature range.

File format: PDF Size:279 KB

The EL1537A is a very low power dual channel differentiated amplifier designed for central office line driving for DMT ADSL solutions. The EL1537A has a higher output swing specification for driving 30Ω loads as compared to the EL1537. This device features a high drive capability of 400mA while consuming only 7.5mA of supply current per amplifier from ±12V supplies. This driver achieves a typical distortion of less than -75dBc, at 1MHz into a 50Ω load. The EL1537A is available in the thermally-enhanced 28 Ld HTSSOP package. This device is specified for operation over the full -40°C to +85°C temperature range. The EL1537A has two control pins, C0 and C1, per channel. With the selection of C0 and C1, the device can be set into full-IS power, 3/4-IS power, 1/2-IS power, and power-down disable modes. The EL1537A maintains excellent distortion and load driving capabilities even in the lowest power settings. The EL1537A has extended bandwidth and improved THD and slew rate for ADSL2+ and VDSL applications.

File format: PDF Size:53 KB

The EL1537 is a very low power dual channel differentiated amplifier designed for central office line driving for DMT ADSL solutions. This device features a high drive capability of 400mA while consuming only 7.5mA of supply current per amplifier from ±12V supplies. This driver achieves a typical distortion of less than -75dBc, at 1MHz into a 50Ω load. The EL1537 is available in the thermally-enhanced 28-pin HTSSOP package. This device is specified for operation over the full -40°C to +85°C temperature range. The EL1537 has two control pins, C0 and C1, per channel. With the selection of C0 and C1, the device can be set into full-IS power, 3/4-IS power, 1/2-IS power, and power-down disable modes. The EL1537 maintains excellent distortion and load driving capabilities even in the lowest power settings. The EL1537 has extended bandwidth and improved THD and slew rate for ADSL2+ and VDSL applications.

File format: PDF Size:52 KB

The EL1529 is a dual channel differential DSL line driver for Globespan's G7566-850 CO chipsets for high performance long reach and high speed applications, including ADSL2, ADSL2+, G.Span, and G.Span+. The EL1529 is an integral part of the signal chain. The driver has been optimized for flat gain response and reduced harmonic distortion and noise in the bands of interest to improve the overall signal to noise in the system. These drivers achieve a total harmonic distortion (THD) measurement of typically -70dB @ 1.1MHz, while consuming typically 5mA per DSL channel of total supply current. This supply current can be set using a resistor on the IADJ pin. Two other pins (C0 & C1) can also be used to adjust supply current to one of four pre-set modes (full-IS, 3/4-IS, 1/2-IS, and full power-down). The EL1529 operates on ±5V to ±12V supplies and retains its bandwidth and linearity over the complete supply range. The device is supplied in the small footprint (4x5mm) 24-pin QFN package and is specified for operation over the full -40°C to +85°C temperature range.

File format: PDF Size:46 KB

The EL1528 is a dual channel differential amplifier designed for driving full rate ADSL signals at very low power dissipation. The high drive capability of 450mA makes this driver ideal for both CAP and DMT designs. It contains two pairs of wideband, high-voltage, current mode feedback amplifiers optimized for low power consumption in DSL systems. These drivers achieve an MTPR distortion measurement of better than 70dB, while consuming typically 5mA per DSL channel of total supply current. This supply current can be set using a resistor on the IADJ pin. Two other pins (C0 & C1) can also be used to adjust supply current to one of four pre- set modes (full-IS, 3/4-IS, 1/2-IS, and full power-down). The EL1528 operates on ±5V to ±12V supplies and retains its bandwidth and linearity over the complete supply range. The device is supplied in a thermally-enhanced 20-pin HTSSOP and the small footprint (4x5mm) 24-pin QFN packages. The EL1528 is specified for operation over the full -40°C to +85°C temperature range.

File format: PDF Size:82 KB

The EL1527 is a very low power dual channel differentiated amplifier designed for central office and customer premise line driving for DMT ADSL solutions. This device features a high drive capability of 400mA while consuming only 7.5mA of supply current per amplifier from ±12V supplies. This driver achieves a typical distortion of less than -75dBc, at 1MHz into a 50Ω load. The EL1527 has two control pins, C0 and C1, per channel. With the selection of C0 and C1, the device can be set into full-IS power, 3/4-IS power, 1/2-IS power, and power-down disable modes. The EL1527 maintains excellent distortion and load driving capabilities even in the lowest power settings. The EL1527 is available in the thermally-enhanced 28 Ld HTSSOP package. This device is specified for operation over the full -40°C to +85°C temperature range.

File format: PDF Size:43 KB

The EL1526 is a dual channel differential DSL line driver designed for high performance ADSL applications using Centillium's Maximus CO chipset. It supports the use of ADSL downstream spectrum up to 3.75MHz, which is beyond the traditional 1.1MHz range. With the High-Bit-Loading (HBL) feature of the Maximus CO chipset, payload rates up to 50Mbps can be achieved in the extended spectrum. This feature allows DMT tones to carry more than 15 bits per tone, resulting in higher performance ADSL services. The EL1526 is an integral part of the signal chain for HBL, optimized for flat gain response and reduced harmonic distortion and noise in the bands of interest. It eliminates the need for external common mode snubber filters in active termination applications with its unique internal compensation circuit. The drivers achieve a total harmonic distortion (THD) measurement of typically -64dB @ 2.2MHz, while consuming typically 5mA per DSL channel of total supply current. The supply current can be set using a resistor on the IADJ pin, and four pre-set modes (full-IS, 3/4-IS, 1/2-IS, and full power-down) can be selected using the C0 and C1 pins. The EL1526 operates on ±5V to ±12V supplies and maintains its bandwidth and linearity over the complete supply range. The device is supplied in a small footprint package.

File format: PDF Size:47 KB

The EL1519 is a dual operational amplifier designed for customer premise line driving in DMT ADSL solutions. This device features a high drive capability of 250mA while consuming only 7.1mA of supply current per amplifier and operating from a single 5V to 12V supply. This driver achieves a typical distortion of less than -85dBc, at 150kHz into a 25Ω load. The EL1519 is available in the industry standard 8 Ld SO. This device is optimized to use low feedback resistor values to minimize noise in ADSL systems. The EL1519 is ideal for ADSL, SDSL, HDSL2 and VDSL line driving applications.

File format: PDF Size:195 KB

The EL1517A is a dual operational amplifier designed for VDSL and ADSL line driving in DMT based solutions. This device features a high drive capability of 250mA while consuming only 7mA of supply current per amplifier and operating from a single 5V to 12V supply. This driver achieves a typical distortion of -80dBc, at 150kHz into a 25Ω load. The EL1517A is available in a 10 Ld HMSOP package and is specified for operation over the full -40°C to +85°C temperature range. The device has control pins C0 and C1 for controlling the bias and enable/disable of the outputs. These controls allow for lowering the power to fit the performance/power ratio for the application. The EL1517A is ideal for ADSL, SDSL, HDSL2 and VDSL line driving applications. The “A” suffix is used only for package leadframe distinction between EL1517. All performance graphs in this datasheet were generated for EL1517IS and EL1517IL. There is no significant electrical difference between EL1517AIYE and the performance curves for EL1517IL. The EL1517A can only be used for single supply.

File format: PDF Size:37 KB

The EL1517 is a dual operational amplifier designed for VDSL and ADSL line driving in DMT based solutions. This device features a high drive capability of 250mA while consuming only 7mA of supply current per amplifier and operating from a single 5V to 12V supply. This driver achieves a typical distortion of -80dBc, at 150kHz into a 25Ω load. The EL1517 is available in the industry-standard 8 Ld SOIC and the thermally-enhanced 16 Ld QFN packages. All are specified for operation over the full -40°C to +85°C temperature range. The 16 Ld QFN package option has control pins C0 and C1 for controlling the bias and enable/disable of the outputs. These controls allow for lowering the power to fit the performance/power ratio for the application. The EL1517 is ideal for ADSL, SDSL, HDSL2 and VDSL line driving applications.

File format: PDF Size:39 KB