intersil Manuals (Industrial)

This document is Intersil's ATE IC product selection guide, introduces the characteristics of Intersil's ATE IC products, including Venus, Non-Venus, DPS/PMU/VI, Pin Drivers and other product lines.

File format: PDF Size:84 KB

This document is the 2008 product selection guide of Intersil Americas Inc., which introduces the features and characteristics of various products such as amplifiers/buffers, comparators, and instrumentation amplifiers.

File format: PDF Size:623 KB

The ISL34340 is a serializer/deserializer of LVCMOS parallel video data. The video data presented to the serializer on the parallel LVCMOS bus is serialized into a high-speed differential signal. This differential signal is converted back to parallel video at the remote end by the deserializer. It also transports auxiliary data bidirectionally over the same link during the video vertical retrace interval.

File format: PDF Size:181 KB

The X9530 is a highly integrated laser diode bias controller which incorporates two digitally controlled Programmable Current Generators, temperature compensation with dedicated look-up tables, and supplementary EEPROM array. All functions of the device are controlled via a 2-wire digital serial interface.

File format: PDF Size:341 KB

This document introduces the features of Intersil X9525. X9525 is a digital controlled potentiometer and EEPROM memory for fiber optic modules

File format: PDF Size:328 KB

The X9523 is an Intersil device released for laser diode control in fiber optic modules. The device has two digitally controlled potentiometers (DCPs), V1/Vcc power-on reset (POR) circuitry, two programmable voltage monitor inputs, and software and hardware indicators. All X9523 functions can be accessed via an industry standard 2-wire serial interface. The DCPs of the X9523 can be used to control the bias and modulation currents of the laser diode in a Fiber Optic module. The programmable POR circuit can be used to ensure that V1/Vcc is stable before power is applied to the laser diode.

File format: PDF Size:361 KB

The X9522 is a laser diode controller for fiber optic modules. It combines three Digitally Controlled Potentiometers (DCPs) and two programmable voltage monitor inputs with software and hardware indicators. All functions of the X9522 are accessed by an industry standard 2-Wire serial interface. It can be used to control the bias and modulation currents of the laser diode in a fiber optic module, as well as monitor various module alarm levels.

File format: PDF Size:337 KB

The X9521 is a chip with features of a digitally controlled potentiometer (DCP), EEPROM memory, and fiber optic module control. It has high resolution and non-volatile characteristics, and can be controlled through a 2-wire serial interface. The X9521 can be used to control the bias and modulation currents of the laser diode in a fiber optic module, and can store module definition data.

File format: PDF Size:324 KB

This datasheet provides detailed information about the X9520, including its features and specifications.

File format: PDF Size:420 KB

The ISL1572 is a dual operational amplifier designed for PLC line driving in OFDM and SSC based solutions. This device features a high drive capability of 750mA while consuming only 6mA of supply current per amplifier and operating from a single 4.5V to 12V supply. The driver achieves a typical distortion of -80dBc, at 150kHz into a 25Ω load. The ISL1572 is available in the thermally-enhanced 16 Ld QFN or 10 Ld HMSOP package and is specified for operation over the full -40°C to +85°C temperature range. The ISL1572 has control pins BIAS0 and BIAS1 for controlling the bias and enable/disable of the outputs. These controls allow for lowering the power to fit the performance/power ratio for the application.

File format: PDF Size:36 KB

ISL1571 is a dual operational amplifier designed for PLC line driving in OFDM and SSC based solutions. It features a high drive capability of 750mA while consuming only 6mA of supply current per amplifier and operating from a single 4.5V to 12V supply. The driver achieves a typical distortion of -80dBc, at 150kHz into a 25Ω load. The ISL1571 is available in the thermally-enhanced 16 Ld QFN or 10 Ld HMSOP package and is specified for operation over the full -40°C to +85°C temperature range.

File format: PDF Size:36 KB

This document introduces the features and characteristics of Intersil CD22M3494 16 x 8 x 1 BiMOS-E Crosspoint Switch.

File format: PDF Size:556 KB

ISL5571A High Voltage Switch

File format: PDF Size:174 KB

ISL5586 is a very low power ringing subscriber interface circuit designed for use with the Broadcom BCM3352 Cable Modem Chip, with on-board voiceband codecs, or other 3.3V voiceband codec devices. The ISL5586 provides on board ringing signal generation up to 95V peak supporting sinusoidal or trapezoidal waveshapes with DC offset. Loop start and ground start trunks are supported, and an open circuit DC voltage of less than 56V is maintained on the subscriber loop in the on-hook condition, in compliance with MTU operation and the safety requirements of UL-1950. Together with the Broadcom BCM3352, the ISL5586 provides resistive and complex two wire impedance matching and transhybrid balancing. Also supported are on- hook transmission of caller id signals, soft and hard polarity reversal and 12/16kHz subscriber pulse metering systems used in Europe and Asia, thereby allowing a low cost, low risk, global product design to be achieved.

File format: PDF Size:528 KB

The 3.3V family of ringing subscriber line interface circuits (SLIC), ISL5585, supports analog Plain Old Telephone Service (POTS) in short and medium loop length, wireless and wireline voice over broadband applications. Ideally suited for customer premise equipment, this family of products offers flexibility to designers with high ringing voltage and low power consumption system requirements. The ISL5585 family is capable of operating with 100V ringing battery supply, which translates directly to the amount of ringing voltage supplied to the subscriber. With the high operating voltage, subscriber loop lengths can be extended to 500Ω (i.e., 5,000 feet) and beyond, allowing this family to serve emerging Fiber In The Loop (FITL) markets. Other key features across the product family include: 3.3V VCC operation, low power consumption, ringing using sinusoidal or trapezoidal waveforms, robust auto-detection mechanisms for when subscribers go on or off hook, and minimal external discrete application components. Integrated test access features are also offered on selected products.

File format: PDF Size:401 KB

The RSLIC-VoIP family of ringing subscriber line interface circuits (RSLIC) supports analog Plain Old Telephone Service (POTS) in short and medium loop length, wireless and wireline applications. Ideally suited for remote subscriber units, this family of products offers flexibility to designers with high ringing voltage and low power consumption system requirements. The RSLIC-VoIP family operates to 100V which translates directly to the amount of ringing voltage supplied to the end subscriber. With the high operating voltage, subscriber loop lengths can be extended to 500Ω (i.e., 5,000 feet) and beyond. Other key features across the product family include: low power consumption, ringing using sinusoidal or trapezoidal waveforms, robust auto-detection mechanisms for when subscribers go on or off hook, and minimal external discrete application components. Integrated test access features are also offered on selected products to support loopback testing as well as line measurement tests. There are five product offerings of the HC55185.

File format: PDF Size:320 KB

This document introduces the features and characteristics of the HC55180, HC55181, HC55183 and HC55184 four ringing SLIC products, including: battery operation to 100V, low standby power consumption of 50mW, peak ringing amplitude 95V, 5 REN, sinusoidal or trapezoidal waveform ringing, robust auto-detection mechanisms for when subscribers go on or off hook, as well as minimal external discrete application components.

File format: PDF Size:327 KB

This document introduces the Intersil HC-5504B EIA/ITU PABX SLIC with 40mA Loop Feed. HC-5504B EIA/ITU PABX SLIC with 40mA Loop Feed is a single IC chip that integrates many of the BORSHT functions.

File format: PDF Size:182 KB

The HC5503T is a low cost Subscriber Line Interface Circuit (SLIC) from Intersil that replaces the components of a discrete Transformer Analog circuit design. The monolithic integrated design provides improved performance and system reliability. The HC5503T provides: Current limited DC feed to the subscriber loop, maintains a flat frequency response over the voice band and beyond, has self resetting thermal protection that allows conversation to continue while the fault is present, provides a TTL subscriber off hook indication even in the presence of longitudinal currents, and limits system power consumption on short loops. The HC5503T provides balanced 2-wire transmission and has excellent longitudinal balance, while providing on hook transmission and longitudinal current rejection in both the on-hook or off-hook conditions. The SLIC needs only one +5V supply in addition to the main battery supply for loop current and operates over a range of battery voltages (-24V to -58V). Available in 24SO packaging. The HC5503T is ideally suited as a replacement for discrete line circuits in low cost analog PABXs, small Office/Home Office products or Small Key Systems.

File format: PDF Size:321 KB

HC5503 low cost 24V SLIC for PABX / Key Systems

File format: PDF Size:723 KB