Zhongchuang Zhihe ZH-4041 Three-Phase Electrical Parameter Collector User Manual

User manual for the Zhongchuang Zhihe ZH-4041 three-phase electrical parameter collector, covering specifications, wiring, and Modbus communication.


Zhongchuang Zhihe ZH-4041 Three-Phase Electrical Parameter Collector User Manual - cover page
Brand
中创智合
Category
Monitoring Equipment
Document type
User Manual
Language
Chinese
Pages
10
File format
PDF
File size
620 KB
Published
19 November, 2026
Updated
19 November, 2026
MD5 checksum
2D3DDA539BEC1C156F2D6BAFEC93B795

About this manual

The Zhongchuang Zhihe ZH-4041 is a three-phase electrical parameter collector for measuring AC three-phase circuits, and it can also be used for three single-phase circuits. It uses a high-precision 24-bit dedicated AD chip and provides RS485 or Ethernet RJ45 communication with selectable Modbus-RTU or Modbus-TCP protocol.

The manual documents product variants, performance specifications, dimensions and pin definitions, wiring examples, and Modbus register definitions for reading and writing electrical parameters. This manual is written in Chinese.

What's inside

  • 一、产品概述
  • 二、产品型号
  • 三、性能指标
  • 四、产品外形结构图与引脚定义
  • 五、产品接线图
  • 六、三相四线/三相三线(三表法)智能电量隔离变送器MODBUS通讯协议

Specifications

Input wiringThree-phase four-wire / three-phase three-wire (or three single-phase circuits)
AccuracyVoltage/current 0.2%; power better than 0.5%
Current range10mA, 100mA, 1A, 5A, 10A, 30A, 50A, 100A AC
Voltage range10V, 100V, 250V, 400V, 500V AC
Voltage input impedance2 kΩ/V
Frequency response30 Hz to 1.2 kHz
Operating temperature-20°C to +60°C
Temperature drift≤100 ppm/°C
RMS update time20, 40, 60, 80, 100 (default), 400, 1000 ms
Isolation voltage>2500 VDC
Auxiliary power+10 to +30 VDC, +10 to +55 VDC, or 85 to 265 VAC
Rated power consumption<2 W
Communication baud rates4800, 9600, 19200, 38400, 57600, 115200 bps
Data formatNo/odd/even parity, 8 data bits, 1 stop bit; or no parity, 9 data bits
Default settingsAddress 1, 9600 baud, no parity, 8 data bits, 1 stop bit
AD converterHigh-precision 24-bit dedicated AD chip
Surge withstandInput, output, and power ports withstand surge voltage above 2 kV
Sampling periods20, 40, 60, 80, 100, 400, 1000 ms
Power supply optionsDC 10-30 V, 10-55 V, or AC/DC 85-265 V
Through-hole diameter7.5 mm

Frequently asked questions

What are the default communication parameters?

The default settings are address 1, baud rate 9600, no parity, 8 data bits, and 1 stop bit.

Which wiring modes can be used?

The device supports three-phase four-wire, three-phase three-wire, or three single-phase circuits.

What communication interfaces and protocols are supported?

It supports RS485 or Ethernet RJ45 interfaces and Modbus-RTU or Modbus-TCP protocols.

How should currents above 5 A be measured?

Use an external current transformer; currents above 5 A use through-hole input.

What update time is recommended for variable-frequency signals?

Use a 400 ms data update time for better stability.

Download PDF (620 KB)

More 中创智合 Manuals


View all 中创智合 manuals →