Watlow DIN-A-MITE Style C Solid-State Power Controller User's Manual

Watlow DIN-A-MITE Style C solid-state power controller user's manual: mounting, wiring, specifications, model ordering codes and semiconductor fuse…


Watlow DIN-A-MITE Style C Solid-State Power Controller User's Manual - cover page
Brand
Watlow
Category
SCR
Document type
User Manual
Language
English
Pages
20
File format
PDF
File size
492 KB
Published
16 November, 2026
Updated
16 November, 2026
MD5 checksum
9F1785441E4427F2F637F9FBD68C11F4

About this manual

This user's manual covers the Watlow DIN-A-MITE Style C solid-state power controller (document 0600-0025-0009 Rev Q, dated January 2016). The controller is available for single-phase, 3-phase 2-leg and 3-phase 3-leg operation from 120 to 600V (ac), with current switching capabilities from 30 to 80A depending on the model ordered. Zero-cross variable time base and ac/dc contactor versions are available, and phase angle or phase angle with current limit control is offered on single-phase models. Shorted SCR and open-heater alarm options are available on some zero-cross models.

The manual gives general specifications, input command signal and input control signal types, alarm behavior, agency approvals, and mounting options for DIN rail, back panel and through-wall installation, including terminal wire ranges and torque values. It also contains the DIN-A-MITE C ordering information code, a DC current rating table, output rating curves and a table of semiconductor fuses and fuse holders for applications through 600V (ac).

What's inside

  • General Specifications
  • Alarms (shorted SCR and open heater)
  • Input Command Signal
  • Additional Specifications: Phase Angle, Phase Angle Current Limit and Single Cycle VTB
  • DIN-A-MITE C Ordering Information
  • DC Current Rating Table
  • Semiconductor Fuses
  • Mounting: DIN Rail, Back Panel and Through-Wall

Specifications

Current switching capability30 to 80A depending on model
Maximum surge current1,350 A peak for 16.6 ms
Maximum I2t for fusing9100 A2s
Latching current500 mA minimum
Holding current200 mA minimum
Off-state leakage1 mA maximum at 25°C
Power dissipation1.2 W per amp switched per controlled leg
Storage temperature-40 to +85°C (-40 to 185°F)
Input terminal wire range0.2 to 1.5 mm2 (24 to 16 AWG), 0.5 Nm torque
Line, load and ground terminal wire range2.5 to 25 mm2 (14 to 3 AWG), 2.7 Nm torque
DIN railDIN EN 50022, 35 by 7.5 mm
Weight1.0 to 1.9 kg (2.2 to 4.2 lb) depending on model

Frequently asked questions

What line voltages and phase configurations does the DIN-A-MITE Style C support?

The controller is made for single-phase, 3-phase 2-leg and 3-phase 3-leg operation from 120 to 600V (ac), and is also offered for 24 to 48V (ac) units.

How much current can the DIN-A-MITE Style C switch?

Current switching capability ranges from 30 to 80A, depending on the model ordered.

How often should the line and load terminals be retorqued?

The manual states that line and load terminals should be retorqued every 3 to 6 months, and also after 48 hours to minimize wire cold flow.

What DIN rail does the controller mount on?

It mounts on DIN EN 50022 rail, 35 by 7.5 mm, with a clipping distance between 34.8 mm and 35.3 mm.

Download PDF (492 KB)

More Watlow Manuals


View all Watlow manuals →