Industrial

This product is a high side driver with analog current sense for automotive applications.

The VN772K is a quad smart power solid state relay for complete H-bridge configurations. It has features such as low voltage bridge, linear current limitation, very low standby power dissipation, short circuit protection, status flag diagnostic (open drain), integrated clamping circuits, undervoltage protection and ESD protection.

The VN771K is a low voltage bridge-type quad smart power solid state relay from STMicroelectronics, which features linear current limiting, very low standby power dissipation, short circuit protection, status flag diagnostics (open drain), integrated clamping circuits, undervoltage protection and ESD protection.

The L5959 is a multifunction voltage regulator from ST company. It can be used in car radios. The chip has four outputs: 8.5V@200mA, 8/10V@1000mA (selectable 10V or 8V), 3.3V@100mA (permanent) and 3.3V@800mA (switched power supply). In addition, L5959 has two protected HSD, reset function, battery voltage (under/over) warning output, load dump protection, independent thermal shutdown, overcurrent limitation, storage capacitor output (STCAP), small capacitor required by stability of regulators and all pins ESD protection.

The OP184/OP284/OP484 are single, dual and quad single-supply, 4 MHz bandwidth amplifiers featuring rail-to-rail inputs and outputs. They are guaranteed to operate from +3 to +36 (or ±1.5 to ±18) volts and will function with a single supply as low as +1.5 volts. These amplifiers are superb for single supply applications requiring both ac and precision dc performance. The combination of bandwidth, low noise and precision makes the OP184/OP284/OP484 useful in a wide variety of applications, including filters and instrumentation. Other applications for these amplifiers include portable telecom equipment, power supply control and protection, DAC output amplifier, and ADC input buffer.

L9805E is a super smart power motor driver from ST, which includes 8-bit MCU, RAM, EEPROM, ADC, WDG, timers, PWM and H-bridge driver, etc. It has a supply operating range of 6.4-18V, a maximum oscillator frequency of 16MHz, a maximum internal clock frequency of 8MHz, an oscillator supervisor, a fully static operation, a temperature range of -40°C to +150°C, a user EPROM/OTP of 16K bytes, a data RAM of 256 bytes, a data EEPROM of 128 bytes, a 64-pin HiQUAD64 package, 10 multifunctional bidirectional I/O lines, two 16-bit timers (each timer includes 2 input captures, 2 output compares, external clock input (on timer 1) and PWM and pulse generator modes), two programmable 16-bit PWM generator modules, a CAN peripheral including bus line interface according to 2A/B passive specifications, a 10-bit analog-to-digital converter, a software watchdog for system integrity, a master reset, a power-on reset, a low voltage reset, a 90mΩ DMOS H-bridge, etc.

TDA7540B is an AM/FM car radio tuner IC with stereo decoder and Intelligent Selectivity System (ISS) manufactured by Texas Instruments.

OP184/OP284/OP484 is a precision single-supply, 4MHz bandwidth amplifier featuring rail-to-rail inputs and outputs. It is guaranteed to operate from +3 to +36 (or ±1.5 to ±18) volts and will function with a single supply as low as +1.5 volts.

This document describes a 16-bit MCU called ST10F276E, which features a MAC unit, 832 KB Flash memory, and 68 KB RAM. It has a highly performance 16-bit CPU with DSP functions, a fast instruction cycle time, and a multiply/accumulate unit. It also supports enhanced boolean bit manipulations and single-cycle context switching. The MCU includes various on-chip and external memories, an external bus, an interrupt controller, timers, an A/D converter, and serial channels.

This document describes the VND5012AK-E double channel high side driver with analog current sense for automotive applications. Its features include inrush current active management by power limitation, very low standby current, 3.0V CMOS compatible input, optimized electromagnetic emission, and very low electromagnetic susceptibility.

OP183 / OP283 is a single-supply, 5 MHz bandwidth amplifier with slew rates of 10 V / µs. OP283 is a dual version. Both can operate from voltages as low as 3 volts and up to 36 volts. This combination of slew rate and bandwidth yields excellent single- supply ac performance making them ideally suited for telecom and multimedia audio applications. In addition to its ac characteristics, the OP183 family provides good dc performance with guaranteed 1 mV offset. Noise is a respectable 10 nV / √Hz. Supply current is only 1.2 mA per amplifier. These amplifiers are well suited for single-supply applications that require moderate bandwidths even when used in high gain configu- rations. This makes them useful in filters and instrumentation. Their output drive capability and very wide full power bandwidth make them a good choice for multimedia headphone drivers or microphone input amplifiers. The OP183 and OP283 are available in 8-pin plastic DIP and SO-8 surface mount packages. They are specified over the extended industrial (–40°C to +85°C) temperature range. One Technology Way, P.O. Box 9106, Norwood. MA 02062-9106, U.S.A. Tel: 617/329-4700 Fax: 617/326-8703 a Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or ot

VND5050AJ-E and VND5050AK-E are double channel high side drivers with analog current sense for automotive applications. They feature main inrush current active management, very low standby current, 3.0 V CMOS compatible input, optimized electromagnetic emission, and very low electromagnetic susceptibility.

VND5050J-E VND5050K-E double channel high side driver for automotive applications. The features of the driver include: main inrush current active management by power limitation, very low standby current, 3.0 V CMOS compatible input, optimized electromagnetic emission, very low electromagnetic susceptibility, compliance with the 2002/95/EC European directive, diagnostic functions, open drain status output, on-state open load detection, off-state open load detection, thermal shutdown indication, undervoltage shutdown, overvoltage clamp, output stuck to VCC detection, load current limitation, self limiting of fast thermal transients, protection against loss of ground and loss of VCC, thermal shutdown, reverse battery protection (see Figure 28) and electrostatic discharge protection. Applications include all types of resistive, inductive and capacitive loads

The ST10F273E 16-bit MCU is a high-performance MCU introduced by ST company. It has a 31.25ns instruction cycle time and a maximum CPU clock of 64 MHz. It has 512Kbyte of Flash memory and 36Kbyte of RAM.

The TDA7333N circuit is a RDS/RDBS signal processor, intended for recovering the inaudible RDS/RBDS informations which are transmitted on most FM radio broadcasting stations.