Industrial

L4995 is a family of monolithic integrated 5 V voltage regulators with a low drop voltage at currents of up to 500 mA, available in both 12 and 24 pin packages

ST10F272M is a 16-bit MCU with 256 Kbyte Flash memory and 20 Kbyte RAM. Features include 50ns instruction cycle time, 40 MHz maximum CPU clock, multiply/accumulate unit (MAC), 16 x 16-bit multiplication, 40-bit accumulator, enhanced boolean bit manipulations and single-cycle context switching support.

This document describes the features and characteristics of the TDA7850 high-power car radio power amplifier, including high output power capability, MOSFET output power stage, 2Ω driving capability, Hi-Fi class distortion, and low output noise.

The OP196/OP296/OP496 are micropower, rail-to-rail input and output operational amplifiers with low power, high open-loop gain, and high bandwidth. They are suitable for battery monitoring, sensor conditioning, portable power supply control, and portable instrumentation applications.

VND5025LAK-E is a dual channel high side driver with analog current sense for automotive applications.

The OP193 family is a single-supply operational amplifier with high precision, low supply current, and the ability to operate at low voltages. It is suitable for applications such as digital scales, strain gages, portable medical equipment, battery-powered instrumentation, and temperature transducer amplifiers.

This document introduces the features of TDA7564B, including Multipower BCD technology, MOSFET output power stage, DMOS power output, high efficiency (class SB), high output power capability, maximum output power, full I2C bus driving, full fault protection, DC offset detection, four independent short circuit protection, clipping detector (2%/10%), linear thermal shutdown and multiple thermal warnings

TDA7563B is a four-channel power amplifier with multiple functions and built-in diagnostic features. It uses multipower BCD technology and MOSFET output stage, with high efficiency and high output power capability. The product features full fault protection and linear thermal shutdown.

The VNQ5027AK-E is a quad channel high side driver with analog current sense for automotive applications. It features an output current of 42A, 3.0V CMOS compatible input, current sense disable, proportional load current sense, undervoltage shut-down, overvoltage clamp, thermal shutdown, current and power limitation, very low standby current, protection against loss of ground and loss of VCC, very low electromagnetic susceptibility, optimized electromagnetic emission, and reverse battery protection.

The VNH3SP30-E is a full-bridge motor driver intended for a wide range of automotive applications. It features a 30A output current, 5V logic level compatible inputs, undervoltage and overvoltage shutdown, overvoltage clamp, thermal shutdown, cross-conduction protection, linear current limiter, and low standby power consumption.

The OP191, OP291 and OP491 are single, dual and quad micropower, single-supply, 3 MHz bandwidth amplifiers featuring rail-to-rail inputs and outputs. All are guaranteed to operate from a 3 volt single supply as well as ±5 volt dual supplies.

TDA7512F is an FM car-radio tuner IC with intelligent selectivity system (ISS). It features RF AGC generation by RF and IF detection, I/Q mixer for 1st FM IF 10.7 MHz with image rejection, 2 programmable IF-gain stages, mixer for 2nd IF 450 kHz, internal 450 kHz bandpass filter with three bandwidths controlled by ISS, fully integrated FM-demodulator with noise cancellation, and more.

The OP186 is a single-supply operational amplifier featuring rail-to-rail outputs. Specifications are guaranteed at +2.2 V, +2.7 V, and +5.0 V single supply as well as ±5 V dual supplies.

TDA7342EQ2N is a digitally controlled audio processor with the following features: input multiplexer, two stereo and one mono inputs, one quasi differential input, selectable input gain for optimal adaptation to different sources, fully programmable loudness function, volume control in 0.3dB steps including gain up to 20dB, zero crossing mute, soft mute and direct mute, bass and treble control, four independent speakers control in 1.25dB steps for balance and fader facilities, independent mute function, all functions programmable via serial I2C bus.

The TDA7303 is a digital controlled stereo audio processor with loudness function, suitable for car radios, Hi-Fi and portable systems. It features selectable input gain and external loudness function. Control is accomplished by serial I2C bus microprocessor interface.