SGS-THOMSON manuals, page 4
SGS-THOMSON GAL16V8AS Data Sheet
SGS-THOMSON M54 /74HC90/691M54/74HC692/693 handbook
The M54/74HC690/691/692/693 are high-speed CMOS counters/registers fabricated in silicon gate C2MOS technology. They offer the high-speed performance of LSTTL combined with the low power consumption of CMOS. The internal circuit consists of three stages, including a buffer output, which provides high noise immunity and stable output. These devices integrate a synchronous counter, a four-bit D-type register, and quadruple two-line to one-line multiplexers with three-state outputs in a single 20-pin package. The counter can be programmed using the data inputs and features enable P and enable T inputs for easy expansion. The device can function as either a counter or a parallel register output.
SGS-THOMSON M28C16 handbook
The document describes the features and characteristics of the M28C16 16K (2K x 8) parallel EEPROM, including fast access time, low power consumption, fast write cycle, and data protection.
SGS-THOMSON MK45H01.02.03 Data Sheet
SGS-THOMSON VNW50N04A Data Sheet
VNW50N04A is a monolithic device made using SGS-THOMSON Vertical Intelligent Power M0 Technology, intended for replacement of standard power MOSFETS in DC to 50 KHz applications. Built-in thermal shut-down, linear current limitation and overvoltage clamp protect the chip in harsh enviroments. Fault feedback can be detected by monitoring the voltage at the input pin.
SGS-THOMSON UCN4801A Data Sheet
Search UCN4801A suppliers
SGS-THOMSON M54HC4351/52/53 M74HC4351/52/53handbook
M54HC4351/52/53 is a high-speed bipolar CMOS logic gate circuit produced by National Semiconductor. It consists of 8 three-terminal bidirectional switches. Its characteristic is that 5V logic signal can be used to control ±5V analog signal, fast switching speed, low switch resistance, high output voltage ratio, wide input voltage range, strong anti-interference ability and low power consumption
SGS-THOMSON M494 SINGLE-CHIP VOLTAGE TUNING SYSTEM WITH 4 ANALOG CONTROLS AND P INTERFACEhandbook
The M494 is a monolithic LSI integrated circuit fabricated in SGS-THOMSON's EPM2 process; an N-channel, Planox, double poly MOS process capable of including a floating gate NV memory cell (EEPROM). The i.c. has been designed as a complete digital TV tuning system based on the voltage synthesis principle and as a replacement for all the conventional tuners.
SGS-THOMSON GS-DC200 Family Data Sheet
The GS-DC200 series is a family of single Eurocard boards that contain all the logic necessary to operate a stepper motor, including the instructions decoding, the step timing generation, the storage of the program to be executed. The motor interface can deliver phase current up to 2.5A. The boards can be used as a stand alone complete motion control system or they can be driven by a central host computer. The GS-DC200 family isbuilt around the GS-C200, GS-C200S, GS-D200, GS-D200S modules, (see the relevant data sheet) and it retains all the features of these modules.
SGS-THOMSON M74HC646 M74HC648 Data Sheet
SGS-THOMSON MJ802 MJ4502 Data Sheet
SGS-THOMSON F0810xH Data Sheet
SGS-THOMSON UAA4713 Data Sheet
UAA4713 is a monolithic integrated circuit intended to control triac or relay switch for AC-mains timer applications. The device can be used in a wide range of industrial and consumer applications such as light control, automatic door opening detector, fire alarm, fluid level control, etc. The circuit processes the output signal of an infrared pyroelectric detector which senses temperature changes caused by heat radiation of the human body. If the sensor detects a temperature change, a programmable timer will start and switch a lamp or other loads to the mains. A further input for a photo-resistive sensor allows to program circuit operation depending on the daylight intensity. Internal circuits avoid false triggering of the external actuators.
SGS-THOMSON ST7272 Data Sheet
SGS-THOMSON ETC9410 Data Sheet