ST Manuals

The L6386E is a high-voltage high and low side driver with features such as high voltage rail, dV/dt immunity, driver current capability, fast switching times, CMOS/TTL inputs, and under-voltage lockout.

The L6387E is a high-voltage high and low side driver from ST company, with 600V voltage rail, dV/dt immunity ±50V/nsec, 400mA source, 650mA sink, 50/30nsec rise/fall time, CMOS/TTL Schmitt trigger inputs, internal bootstrap diode, outputs in phase with inputs, interlocking function and other features.

The L6388E is a high-voltage high and low side driver with features such as high-voltage rail, dV/dt immunity, and high driver current capability.

This is a datasheet for VNI4140K Quad high-side smart power solid-state relay. The relay has an output current of 0.7 A per channel, shorted load protections, and temperature protections.

The VN808-32-E is an eight-channel high side driver with VCC/2 compatible input, junction overtemperature protection, case overtemperature protection, current limitation, shorted load protection, undervoltage shut-down, protection against loss of ground, very low stand-by current and compliance to 61000-4-4 IEC test up to 4 kV.

The L6390 is a high-voltage half bridge driver for N-channel Power MOSFETs or IGBT. It features a high-voltage rail, integrated operational amplifier and comparator for advanced current sensing and fault protection.

The L6392 is a high-voltage high and low side driver with features including high voltage rail up to 600V, dV/dt immunity of ±50V/nsec, driver current capability of 290mA source - 430mA sink, fast switching times, 3.3V and 5V TTL/CMOS inputs, integrated bootstrap diode, operational amplifier for current sensing, adjustable dead-time, interlocking function, compact layout, and bill of material reduction.

L6393 is a high-voltage half-bridge gate driver with features such as high voltage rail, dV/dt immunity, high driver current capability, fast switching times, etc. It is suitable for motor drivers in home appliances, factory automation, industrial drives and fans, HID ballasts, and power supply units.

L6386AD is a high voltage driver from ST company. It can drive power MOS or IGBT with up to 600V voltage rail.

The STUSBCD01B is a USB charger detection IC from ST company, which can detect dedicated USB chargers, Host/Hub chargers or standard host ports connected to the USB DP/DM data lines. The device implements two different detection methods in order to be able to distinguish between a dedicated charger and a Host/Hub charger. Operation is controlled through three general purpose I/O pins; a hardware open drain detection output is also available. An internal regulator provides the 1.8 V supply voltage for the internal blocks and state machine while a clamping device prevents VBUS voltage from going over 6 V (typ.). The STUSBCD01B is available in a 12 bumps Flip-Chip 0.4 mm pitch package.

VNI2140J is a monolithic device designed using STMicroelectronics' VIPower technology. The device drives two independent resistive or inductive loads with one side connected to ground. Active current limitation prevents a drop in system power supply in cases of shorted-load, and built-in thermal shutdown protects the chip from damage due to over-temperature and short-circuit. In overload conditions, channel turns OFF and ON automatically to maintain the junction temperature between TTSD and TR. If the case temperature reaches TCSD, the overloaded channel is turned OFF and restarts only when case temperature decreases down to TCR. In order to avoid high-peak current from the supply, when more than one channel is overloaded the TCSD restart is not simultaneous. Non overloaded channels continue to operate normally. The open-drain diagnostic outputs are used to detect overload and turn-off status.

The VNI8200XP is an octal high-side smart power solid state relay with serial/parallel selectable interface on chip. It features 0.7 A output current, short-circuit protection, 8-bit and 16-bit SPI interface, channel overtemperature detection and protection, thermal independence of separate channels, drives all types of loads (resistive, capacitive, inductive load), GND loss protection, Power Good diagnostic, undervoltage shutdown with hysteresis, overvoltage protection (VCC clamping), very low supply current, common fault open drain output, IC warning temperature detection, channels output enable, 100 mA high efficiency step-down switching regulator with integrated boot diode, adjustable regulator output, switching regulator disable, 5 V and 3.3 V compatible I/Os, channel outputs status LED driving 4 x 2 multiplexed array, fast demagnetization of inductive loads, ESD protection.

The STUSB06E is a single chip USB transceiver that complies with the USB v2.0 standard. It supports full-speed (12 Mbps) and low-speed (1.5 Mbps) operation, has low power consumption, supports charger detection, and supports sharing mode.

This product is a programmable poly-phase energy calculator IC that supports 1-, 2- or 3-phase WYE and Delta services, from 2 to 4 wires, computes cumulative active and reactive wide-band and fundamental harmonic energies, computes active and reactive energies, RMS and momentary voltage and current values for each phase, supports Rogowski coil, current transformer, Shunt or Hall current sensors, exclusive ripple-free energy calculation algorithm, programmable pulsed output, stepper motor outputs, neutral current, temperature, and magnetic field monitoring, OTP memory for configuration and calibration, SPI interface, supports IEC 62052-11 / 62053-21 / 62053-23 standards, less than 0.1 % error over 1:1000 dynamic range