ST Manuals

STPMS1 is a smart sensor device produced by ST company. It is used in power metering, motor control, industrial process control, weight scale and pressure transducers.

STPMS2 Smart sensor II is a dual-channel 1-bit, 4 MHz, second-order sigma-delta modulator with embedded PGLNA.

ST802RT1A ST802RT1B 10/100 real-time Ethernet 3.3 V transceiver is a high-performance fast Ethernet physical layer interface for 10Base-T, 100Base-TX and 100Base-FX applications.

This document provides information on the ST8024L smartcard interface product, which is designed to be compatible with the NDS conditional access system, and is ISO 7816, GSM11.11, and EMV 4.2 compatible. It features an IC card interface, can be powered by 3V or 5V, and has three specifically protected half-duplex bi-directional buffered I/O lines, among other capabilities.

STPM10 is a programmable single-phase energy metering IC with tamper detection features. It can measure active, reactive, and apparent energies, current, voltage RMS, and instantaneous measurement, frequency measurement, etc. It has a ripple-free active energy pulsed output and live and neutral monitoring for tamper detection. It supports fast and simple one-point digital calibration over the whole current range. It has integrated linear voltage regulators for digital and analog supply. It supports 50 - 60 Hz - IEC62052-11, IEC62053-2x specifications. The error is less than 0.1% in the 1000:1 range. It has a precision voltage reference of 1.23 V with a maximum temperature coefficient of 30 ppm/°C.

The L6391 is a high-voltage high and low side driver from ST. It supports up to 600V input voltage and has overcurrent, overtemperature protection functions. It is suitable for home appliances, industrial drives, fans, etc.

The TD352 is ST's latest generation of IGBT/MOSFET gate driver, with 1.7A sink current and 1.3A source current. It features active Miller clamp function, desaturation detection, adjustable turn-on delay, UVLO protection and 2kV ESD protection. It is suitable for 1200V three-phase inverters, motor control systems and UPS applications.

ST8024 is a smartcard interface of STMicroelectronics, which supports ISO 7816, GSM11.11 and EMV (payment systems) standards and is compatible with NDS conditional access systems.

The VN808-E is an octal channel high side driver with VCC/2 compatible input, junction overtemperature protection, thermal independent case overtemperature protection, current limitation, shorted load protection, undervoltage shut-down, protection against loss of ground, very low standby current and compliance to 61000-4-4 IEC test up to 4 kV.

The VN808CM-E is an eight-channel high side driver. It is designed in STMicroelectronics VIPower M0-3 technology and is intended for driving any type of load with one side connected to ground. It can be driven using a 3.3V logic supply. Active current limiting combined with thermal shutdown and automatic restart protects the device against overload. In overload condition, channel turns OFF and back ON automatically so as to maintain junction temperature between TTSD and TR. If this condition makes case temperature reach TCSD, overloaded channel is turned OFF and will restart only when case temperature has decreased down to TCR(see waveform 3 Figure 6 on page 10). Non overloaded channels continue to operate normally. Device automatically turns OFF in case of ground pin disconnection. This device is especially suitable for industrial applications conform to IEC 61131.

This document describes the features and characteristics of the VN330SP-32-E quad high side smart power solid state relay, including output current, digital input voltage, shorted load and overtemperature protections, built-in current limiter, undervoltage shut-down, etc.

This document is the datasheet of VN340SP-E, which mainly introduces the features and characteristics of the product

VN340SP-33-E is a quad high side smart power solid state relay with an output current of 1A per channel and various protection features. It is designed for driving four independent resistive or inductive loads.

The VN330SP-E is a quad high side smart Power solid state relay with an output current of 0.7A per channel, a digital input clamped at 32V minimum voltage, shorted load and overtemperature protections, built-in current limiter, undervoltage shut-down, open drain diagnostic output, and fast demagnetization of inductive loads. It conforms to IEC 61131-2.