ST Manuals

The 74VCX162245 is a low voltage CMOS 16 BIT BUS TRANSCEIVER (3-STATE) fabricated with sub-micron silicon gate and five-layer metal wiring C2MOS technology. It is ideal for low power and very high speed 1.8 to 3.6V applications; it can be interfaced to 3.6V signal environment for both inputs and outputs

The 74VCX162244 is a low voltage CMOS 16 BIT BUS BUFFER (NON INVERTED) fabricated with sub-micron silicon gate and five-layer metal wiring C2MOS technology. It is ideal for low power and very high speed 1.8 to 3.6V applications; it can be interfaced to 3.6V signal environment for both inputs and outputs. Any nG output control governs four BUS BUFFERS. Output Enable input (nG) tied together gives full 16-bit operation. When nG is LOW, the outputs are on. When nG is HIGH, the output are in high impedance state. This device is designed to be used with 3 state memory address drivers, etc. The device circuits is including 26Ω series resistance in the outputs. These resistors permits to reduce line noise in high speed applications. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and trans

74VCX162244 is a 16-bit buffer with low voltage, high speed, low power, 3.6V input and output

The TD350E is an advanced IGBT/MOSFET driver with features including 1.5A source/2.3A sink gate drive, active Miller clamp, two-level turn-off with adjustable level and delay, desaturation detection, fault status output, negative gate drive capability, input compatible with pulse transformer or optocoupler, separate sink and source outputs for easy gate driving, UVLO protection, and 2kV ESD protection. It is suitable for use in 1200V, 3-phase inverters, motor control, and UPS systems.

The VNI4140K-32 is a quad high side smart power solid state relay with features such as 1A output current per channel, shorted load protections, overtemperature protection, etc.

L6360 IO-Link communication master transceiver IC Datasheet - production data

The L6385E is an STMicroelectronics high-voltage high and low side driver, featuring high voltage rail up to 600V, dv/dt immunity ±50V/nsec, switching times 50/30 ns rise/fall, 1nF load, CMOS/TTL Schmitt trigger inputs, under voltage lock out and outputs in phase with inputs.

This document introduces the features and characteristics of ST's L6384E high-voltage half bridge driver product, including high voltage rail range, driver current capability, switching time, logic input type, dead time setting, under voltage lockout, integrated bootstrap diode, and capacitor clamping.

The L6375D is a monolithic intelligent power switch in BCDmultipower technology, for driving inductive or resistive loads with controlled output voltage slew rate and short-circuit protection. It features a 0.5 A output current, 8 V to 35 V supply voltage range, internal current limiting, thermal shutdown, open ground protection, internal negative voltage clamping for fast demagnetization, differential inputs with large common mode range and threshold hysteresis, undervoltage lockout with hysteresis, open load detection, two diagnostic outputs, output status LED driver, non-dissipative short-circuit protection, immunity against burst transient (IEC 61000-4-4), and ESD protection (human body model ±2 kV).

The device is specifically designed to provide all the necessary features to implement a single phase energy meter without any other active component.

STUSB03E is a USB transceiver produced by ST company. It supports USB 2.0 protocol with a speed of up to 12Mbps. It supports low power consumption and low voltage power supply, and is suitable for PDAs, MP3 players and mobile phones.

The L9524C is a control IC for up to six glow plugs of diesel engines. The glow plugs are switched by up to four external PWM-controlled N-channel Power MOSFETs or a single relay in high-side configuration. Supply voltage, battery voltage, junction temperature, switches, currents through the glow plugs, and charge pump voltage are monitored. A two-wire interface is used to communicate with the diesel engine management system.

The L6375S is a monolithic intelligent power switch with a high-side driver function. It has a 0.5A output current, a supply voltage range of 8V to 35V, internal current limiting and thermal shutdown, open ground protection, internal negative voltage clamping for fast demagnetization, differential inputs with a large common mode range and threshold hysteresis, undervoltage lockout with hysteresis, open load detection, two diagnostic outputs, an output status LED driver, non-dissipative short-circuit protection, immunity against burst transient (IEC 61000-4-4), and ESD protection.

The TDE1708DFT intelligent power switch has a low side or high side switch configuration, a supply voltage range of 6V to 48V, overload and short circuit protections, internal voltage clamping, supply and output reversal protection, thermal shutdown, GND and VS open wire protection, adjustable delay at switch on, indicator status LED driver, +5V regulated aux. voltage, and high burst immunity.