ON Manuals

NTF5P03T3 is a P-channel MOSFET from onsemi company. Its main feature is RDS(on) as low as 100 mΩ. It can be used for DC-DC converters, power management, motor control, etc.

The MC1488 is a monolithic quad line driver designed to interface data terminal equipment (DTE) with data communications equipment (DCE) in conformance with the specifications of EIA Standard No. EIA-232D.

The MC14099B is an 8-bit addressable latch. Data is entered in serial form when the appropriate latch is addressed (via address pins A0, A1, A2) and write disable is in the low state. For the MC14099B the input is a unidirectional write only port. The data is presented in parallel at the output of the eight latches independently of the state of Write Disable, Write/Read or Chip Enable. A Master Reset capability is available on both parts.

MC14538B/D Dual Precision Retriggerable/Resettable Monostable Multivibrator

The NCP3163 is a 3.4 A, 50 to 300 kHz step-up/down/inverting switching regulator that can be used in step-down, step-up, or voltage-inverting applications. This controller was specifically designed to be incorporated in step-down, step-up, or voltage-inverting applications with a minimum number of external components.

The NCP1523 is a 3 MHz, 600mA, high efficiency, adjustable output voltage step-down converter, optimized for portable applications powered from a 1-cell Li-ion or 3 cell Alkaline/NiCd/NiMH battery. The device is available in an adjustable output voltage from 0.9V to 3.3V. It uses synchronous rectification to increase efficiency and reduce external part count. The device also has a built-in 3 MHz (nominal) oscillator which reduces component size by allowing use of a small inductor and capacitors. NCP1523 is available in automatic switching PWM/PFM (NCP1523FCT2G) improving system efficiency and in PWM mode only (NCP1523BFCT2G) offering a very efficient load transient solution. Additional features include integrated soft-start, cycle-by-cycle current limiting and thermal shutdown protection. The NCP1523 is available in a space saving, 8 pin chip scale package.

The BC856ALT1 series is a preferred series of general purpose PNP silicon transistors. The series features lead-free packaging.

MC14040B is a 12-stage binary counter constructed with MOS P-Channel and N-Channel enhancement mode devices in a single monolithic structure. It features fully static operation, diode protection on all inputs, a wide supply voltage range, and the ability to drive low-power TTL loads. It is commonly used in time delay circuits, counter controls, and frequency-driving circuits.

The MC74HC374A is an octal 3-state non-inverting D flip-flop manufactured using high-performance silicon-gate CMOS technology. It has the same pinout as the LS374 and its inputs are compatible with standard CMOS outputs. Data meeting the setup time is clocked to the outputs with the rising edge of the clock. The Output Enable input does not affect the states of the flip-flops, but when Output Enable is high, the outputs are forced to the high-impedance state. The HC374A is identical in function to the HC574A which has the input pins on the opposite side of the package from the output. This device is similar in function to the HC534A which has inverting outputs.

MC14518B/D is a dual BCD counter and a dual binary counter produced by Semiconductor Components Industries, LLC. It is constructed with MOS P-channel and N-channel enhancement mode devices in a single monolithic structure.

This document introduces a self-protected field-effect transistor (FET) product with temperature and current limit features. The product utilizes ON Semiconductor's latest MOSFET technology process to achieve the lowest possible on-resistance per silicon area while incorporating smart features. Integrated thermal and current limits work together to provide short circuit protection. The product also features an integrated drain-to-gate clamp that enables it to withstand high energy in the avalanche mode and provides additional safety margin against unexpected voltage transients. Electrostatic discharge (ESD) protection is provided by an integrated gate-to-source clamp.

The MMSZ2V4T1/D 500 mW SOD−123 Surface Mount Zener Voltage Regulators offer 500 mW rating on FR−4 or FR−5 board, wide Zener reverse voltage range of −2.4 V to 56 V, package designed for optimal automated board assembly, small package size for high density applications, ESD rating of Class 3 (>16 kV) per Human Body Model, and Pb−free packages. It is ideal for automotive, industrial, and power applications.

The NL37WZ16 is a high performance buffer with inputs operating from a 1.65 to 5.5 V supply. The NL37WZ16 can be used as a line receiver which will receive slow input signals.