intersil Manuals

The HI3256 is an 8-bit, high-speed, flash analog-to-digital converter optimized for high speed, low power, and ease of use. With a 120MSPS encode rate capability and full-power analog bandwidth of 250MHz, this component is ideal for applications requiring the highest possible dynamic performance.

The document introduces a series of radiation-hardened MOSFET products developed by Intersil Corporation. These products feature resistance to Single Event Effects (SEE), particularly Single Event Gate Rupture (SEGR), making them suitable for commercial and military space applications. The products have a total dose hardness of up to 100K RADS and maintain the necessary dose rate and neutron tolerance for military applications.

This product is a 75A, 55V, 0.007 Ohm, N-Channel UltraFET Power MOSFETs produced by Intersil Corporation. It has high performance, low power consumption, low reverse recovery time and stored charge.

The X9420 is a low noise/low power/SPI Bus single digitally controlled (XDCP™) potentiometer with a SPI serial interface. The potentiometer has a register-oriented format that enables direct read/write/transfer of wiper positions and storage of as many as four positions per potentiometer. The potentiometer is powered by VCC = 2.7V to 5.5V, V+ = 2.7V to 5.5V, and V– = -2.7V to -5.5V. The potentiometer is a CMOS device with standby current of less than 1 µA. The potentiometer is highly reliable and can withstand 100,000 data changes per bit per register and register data retention of 100 years. The potentiometer has 8 bytes of nonvolatile EEPROM memory. The potentiometer's resistor arrays are 10kΩ or 2.5kΩ. The potentiometer's resolution is 64 taps per pot. The potentiometer's packages are 14Ld TSSOP and 16Ld SOIC. The potentiometer is available with lead-free and annealed finishes and is RoHS compliant.

The X80000 is a smart power plug with penta-power sequence controller and hot swap function. It contains three major functions: a power communications controller, a power sequencing controller, and a hotswap controller. The power communications controller allows smart power supply control via the backplane using the SMBus protocol. The system can check for voltage, current, and manufacturing ID compliance before board insertion. The power distribution network can monitor the status of the negative voltage supply, DC voltage supplies, and hardshort events by accessing the Fault Detection Register and General Purpose EEPROM of the device. Each device has a unique slave address for identification. The power sequencer controller time sequences up to five DC-DC modules. The X80000 allows for various hardwired configurations, either parallel or relay sequencing modes. The power good, enable and voltage good signals provide for flexible DC-DC timing configurations. Each voltage enable signal has a programmable delay. In addition, the voltage good signals can be monitored remotely via the fault detection register (thru the SMBus). The hot

X55060 is a battery monitoring chip produced by Intersil company, which has dual voltage monitoring, high and low level reset output, programmable reset threshold, low level output, system battery switching circuit, programmable watchdog timer, 64Kbits EEPROM, built-in inadvertent write protection circuit, 10MHz SPI interface and other features

The HIN232-HIN241 family of RS-232 transmitters/receivers interface circuits meet all EIA RS-232E and V.28 specifications, and are particularly suited for those applications where ±12V is not available. They require a single +5V power supply (except HIN239) and feature onboard charge pump voltage converters which generate +10V and -10V supplies from the 5V supply. The family of devices offer a wide variety of RS-232 transmitter/receiver combinations to accommodate various applications (see Selection Table). The drivers feature true TTL/CMOS input compatibility, slew-rate-limited output, and 300Ω power-off source impedance. The receivers can handle up to ±30V, and have a 3kΩ to 7kΩ input impedance. The receivers also feature hysteresis to greatly improve noise rejection.

The CD22103A is an integrated circuit that performs HDB3 transmission coding and reception decoding functions for 2.048/8.448Mb/s transmission applications. It operates at data rates from 50Kb/s to 10Mb/s, consistent with CCITT G703 recommendations. The product includes HDB3 encoder and decoder sections with code error detection.

ISL6227 is a dual PWM controller from ISL company, which adopts synchronous buck DC/DC converter and can provide power regulation for DDR memory, chipset, graphics and other system electronics. It supports AC/DC adaptor or Li-ion battery pack and automatically switches mode under heavy load and light load to ensure high efficiency under various conditions.

The ISL43840 is a low-voltage, single and dual supply, dual 4 to 1 multiplexer analog switch with enable function. Produced by Intersil, this product is designed to operate from a single +2V to +12V supply or from a ±2V to ±6V supply. Each switch can handle rail to rail analog signals. It features low off-leakage current and a wide range of digital input logic thresholds, making it suitable for various application scenarios.

EL5120, EL5220, and EL5420 are low power, high voltage, rail-to-rail input-output amplifiers. They have a bandwidth of 12MHz, common mode input ability beyond the supply rails, and rail-to-rail output capability.

EL5162, EL5163, EL5262, EL5263, EL5362 500MHz Low Power Current Feedback Amplifiers

Intersil EL5164, EL5165, EL5364 600MHz Current Feedback Amplifiers with Enable is a high bandwidth integrated circuit with 600MHz. It is suitable for high definition video monitoring applications.

MS82C55A, MQ82C55A is a high performance CMOS version of the industry standard 8255A and is manufactured using a self-aligned silicon gate CMOS process (Scaled SAJI IV). It is a general purpose programmable I/O device which may be used with many different microprocessors.