intersil Manuals

HIP6017 Advanced PWM and Dual Linear Power Control for High-Performance Microprocessor and Computer Applications

The X4643/5 is an integrated circuit produced by Intersil, which has an optional watchdog timer, power supply voltage monitor and 64K EEPROM memory function.

X40010/11/14/15 is a voltage monitor chip produced by Intersil. It has dual voltage detection and reset signal generation functions, low power consumption, and is suitable for industrial, computer and other fields.

BCW60, BCX70 are NPN silicon AF transistors for AF input stages and driver applications. Features include high current gain, low collector-emitter saturation voltage and low noise between 30 Hz and 15 kHz. BCW60 and BCW61 are complementary types, with BCW60 being NPN and BCW61 being PNP.

EL2260/EL2460 are dual/quad 130MHz current feedback amplifiers with -3dB bandwidth of 130MHz at a gain of +2

82C84A is a high performance CMOS clock generator driver from Intersil that is designed to service the requirements of both CMOS and NMOS microprocessors such as the 80C86, 80C88, 8086 and the 8088.

The ISL95810 is a single digitally controlled potentiometer with low noise, low power, and an I2C bus interface. It has 256 resistor taps with a resolution of 0.4%, and can be used in various applications such as control, parameter adjustments, and signal processing.

The ISL95711 is a digitally controlled potentiometer (XDCP) with terminal voltage of ±3V or ±5V, 128 taps, and I2C serial interface. It consists of a resistor array, wiper switches, a control section, and nonvolatile memory.

The ISL6753 is a high-performance, low-pin-count alternative zero-voltage switching (ZVS) full-bridge PWM controller. Like the ISL6551, it achieves ZVS operation by driving the upper bridge FETs at a fixed 50% duty cycle while the lower bridge FETS are trailing-edge modulated with adjustable resonant switching delays. Compared to the more familiar phase-shifted control method, this algorithm offers equivalent efficiency and improved overcurrent and light- load performance with less complexity in a lower pin count package. This advanced BiCMOS design features low operating current, adjustable oscillator frequency up to 2MHz, adjustable soft-start, internal over temperature protection, precision deadtime and resonant delay control, and short propagation delays. Additionally, Multi-Pulse Suppression ensures alternating output pulses at low duty cycles where pulse skipping may occur.

The ISL60002 is a high precision, low power voltage reference from Intersil. It features Intersil's proprietary floating gate analog technology, low supply voltage operation and an ultra-low operating current of 400nA. Additional features include guaranteed initial accuracy as low as ±1.0mV, @ 20ppm/°C temperature coefficient and long-term stability of <<10ppm/√1kHrs.

The ISL3990 is a dual-band power amplifier from ISL company. It operates in the ISM and U-NII bands with an output power of 21 dBm (typical). The power supply voltage is 2.7V to 3.6V and the power gain is 28 dB (typical). The working frequency range is 1.8GHz to 2.4GHz and 5.15GHz to 5.825GHz.

The HSP9501 is a 10-bit wide programmable data buffer designed for use in high speed digital systems. It has two operating modes, delay mode and recirculate mode. In delay mode, it can provide 2 to 1281 clock cycles of delay. In recirculate mode, it provides a programmable circular buffer. The length of the buffer or amount of delay can be programmed through the LC0-10 length control input port and the LCEN length control enable port.

The HRP2540 is a high forward current, high reverse energy controlled avalanche power rectifier. It uses an ion-implanted planar epitaxial construction. This device was designed for use as the output rectifier in the three phase six diode bridge assembly of an automotive alternator system. It provides “Load Dump” suppression by virtue of its precisely controlled reverse avalanche breakdown voltage. When used singly it can also serve as a transient suppressor for an automotive accessory. This device can provide for- ward voltage clamping and reverse voltage bypassing. This will protect the accessory from L-C inductive spikes and/or field decay transients.

HIP4020 is a half-bridge power switch chip released by Intersil for driving small-power DC motors. It can drive 3V, 5V and 12V DC motors.