This page provides manuals, user guides, handbooks, instructions, specification, instruction, maintenance manual for Analog Devices Video Player, Industrial Supply, ...
The ADN2531 is a 11.3Gbps laser diode driver that supports 3.3V operation, has a 26ps rise/fall time, supports 10mA to 100mA bias current range and 10mA to 80mA differential modulation current range.
AD8015 is a low cost, wide bandwidth, low noise transimpedance amplifier with 240 MHz bandwidth and 3.0 pA/√Hz input current noise. It is suitable for high bandwidth, low noise fiber optic receivers.
AD8304 is a monolithic logarithmic detector optimized for the measurement of eight full decades of input signals from 100 pA to 10 mA with 0.1 dB conformance
AD8305 is a 100 dB dynamic range 10 nA to 1 mA current converter produced by Analog Devices. It has the following features: 1. Optimized for fiber optic photodiode interface; 2. Measures current over 5 decades; 3. Conforms to 0.1 dB from 10 nA to 1 mA of the law; 4. Single- or dual-supply operation (3 V to 12 V total); 5. Has full log-ratio capabilities; 6. Nominal slope of 10 mV/dB (200 mV/decade); 7. Nominal intercept of 1 nA (set by external resistor); 8. Optional adjustment of slope and intercept; 9. Completely and temperature stable; 10. Rapid response time for a given current level; 11. Miniature 16-lead chip scale package (LFCSP 3 mm × 3 mm); 12. Low power: ~5 mA quiescent current.
The ADL5306 is a low-cost logarithmic converter designed for fiber optic photodiode interfacing. It can measure current over 3 decades with 0.1 dB law conformance. The product can operate on a single or dual supply and has full log-ratio capabilities. It is temperature stable and the slope and intercept can be adjusted using external resistors. The product has a rapid response time, miniature chip scale package, and low power consumption.
The ADN2820 is a high-performance 10.7Gbps 3.3V TIA with an average power monitor. It is optimized for 10Gbps Metro-Access and Ethernet systems and is a single-chip solution for detecting photodiode current with a differential output voltage.
ADL5310 is a low cost, dual logarithmic amplifier from Analog Devices that converts input current over a wide dynamic range to a linear-in-dB output voltage. It is optimized to determine the optical power in wide-ranging applications, such as gain and absorbance measurements.
This document is a reference design manual for 3.3V 2.7 Gb/s Limiting Amplifier ADN2890, introducing the main features and characteristics of the product.
The ADN2892 is a 4.25 Gbps limiting amplifier with integrated loss of signal (LOS) detection circuitry and a received signal strength indicator (RSSI). This part is op
The ADN2891 is a 3.2Gbps limiting amplifier with integrated loss-of-signal (LOS) detection circuitry and a received signal strength indicator (RSSI). This part is optimized for SONET, Gigabit Ethernet (GbE), and Fibre Channel optoelectronic conversion applications. The ADN2891 has a differential input sensitivity of 4 mV p-p and accepts up to a 2.0 V p-p differential input overload voltage. The ADN2891 supports current mode logic (CML) outputs with controlled rise and fall times. 80 ps rise/fall times CML outputs: 700 mV p-p differential Programmable LOS detector: 3.5 mV to 35 mV Rx signal strength indicator (RSSI) SFF-8472-compliant average power measurement Single-supply operation: 3.3 V Low power dissipation: 145 mW Available in
The ADN2880 is a 3.3 V, low noise, transimpedance amplifier with a bandwidth of 3.2 Gbps and a differential transimpedance of 4400 V/A. It is suitable for 3.2 Gbps or below optical receivers, SONET/GbE/FC optical receivers, and PIN/APD-TIA receive optical subassemblies (ROSA).
ADL5317 is a cascade avalanche photodiode (APD) bias controller and wide range (5 nA to 5 mA) current monitor. It accurately sets APD bias voltage with a wide bias range and a 3 V-compatible control interface. The product also monitors photodiode current and features overcurrent protection and overtemperature shutdown.
The ADL5315 is a wide input current range, precision high-side current mirror featuring a stable and user-adjustable input current limit, single-supply operation range of 2.7 V to 8 V, and miniature 8-lead LFCSP (2 mm × 3 mm) package. It is suitable for applications such as optical power monitoring, general voltage biasing with precision current monitoring, and voltage-to-current conversion.
The ADN3000-06 is a complete high speed optical receiver featuring a proprietary large-area germanium PIN photodiode integrated with a transimpedance amplifier (TIA). The integrated photodiode and TIA improve the performance of the optical receiver.
