ANALOG Manuals

The AD5162 is a 2-channel 256-position SPI digital potentiometer with 2.5 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ resistance values. It is available in the MSOP-10 package, has low power consumption, and a wide operating voltage range. It is suitable for applications such as system calibration, electronic level setting, mechanical trimmer replacement, permanent factory PCB setting, transducer adjustment, RF amplifier biasing, and automotive electronics adjustment.

The AD5161 is a 256-position SPI/I2C selectable digital potentiometer from Analog Devices. It has 5kΩ, 10kΩ, 50kΩ, and 100kΩ resistance values, a 3mm x 4.9mm package, support for SPI/I2C communications, single supply power, and a working temperature range of -40°C to +125°C.

This document describes the features and characteristics of the 256-position SPI compatible digital potentiometer AD5160, including 256 positions, end-to-end resistance, compact package, SPI interface, single supply, low power, wide operating temperature range, etc. This product can be used as a replacement for mechanical potentiometers in new designs and is suitable for applications in sensors, RF amplifiers, automotive electronics, etc.

AD515A is a monolithic FET-input operational amplifier with a guaranteed maximum input bias current of 75 fA (AD515AL). The AD515A is a monolithic successor to the industry standard AD515 electrometer, and will replace the AD515 in most applications. The AD515A also delivers laser-trimmed offset voltage, low drift, low noise and low power, a combination of features not previously available in ultralow bias current circuits. All devices are internally compensated, protected against latch-up and are short circuit protected. The AD515A is typically used for sensor and instrumentation measurement, ohmmeter, divider, voltage reference, DC voltage measurement and current sensor applications. The AD515A can be used to measure small currents or voltages from high impedance resistors or capacitors.

The AD5100 is a system management IC with programmable quad voltage monitoring and supervisory functions. It features two high voltage (30V) monitoring inputs and two low voltage (5V) monitoring inputs, with programmable thresholds, delays, and warning functions. Additionally, it includes supervisory functions such as watchdog reset with programmable timeout, failed processor watchdog enabled shutdown, selectable floating watchdog reset function, and manual reset. The IC also has a digital interface and programmability using an I2C compatible interface.

This product is a precision monolithic operational amplifier with high accuracy and fast settling time.

AD5040/AD5060 are single 14/16-bit buffered voltage output DACs from the nanoDAC family. They operate at 3V/5V and come in an 8-pin SOT23 package. They feature a low power serial interface, fast settling, and low power operation.

The AD5011 is an analog front end for two pair or single pair HDSL applications that use 1168 kbps or 2.32 Mbps data rates. The device integrates all the transmit and receive functional blocks.

The ADM811/ADM812 are reliable voltage monitoring devices suitable for use in most voltage monitoring applications. The ADM811/ADM812 are designed to monitor five different voltages, each allowing for a 5% or 10% degradation of standard PSU voltages before a reset occurs. These voltages have been selected for the effective monitoring of +3 V, +3.3 V, and +5 V.

This document introduces the features and characteristics of the ADDC02828SA power module, including 28V dc input, 28V dc @ 3.6 A, 100W output, integrated EMI filter, compliance with MIL-STD-461D standard, low weight of 80 grams, NAVMAT derating, etc.

The AD8325 is a low-cost, digitally controlled line driver with features such as programmable gain, low distortion, and low output noise level.

The AD7732 is a high precision, high throughput analog front end. With a total conversion time of 500 µs (2 kHz channel switching), true 16-bit p-p resolution is achievable, making it ideally suitable for high resolution multiplexing applications. The part can be configured via a simple digital interface, which allows users to balance the noise performance against data throughput up to a 15.4 kHz.

The AD600/AD602 are dual channel, low noise, wideband variable gain amplifiers optimized for use in ultrasound imaging systems, but are applicable to any application requiring very precise gain, low noise and distortion, and wide bandwidth. Each independent channel provides a gain of 0 dB to +40 dB (AD600) and –10 dB to +30 dB (AD602). The AD600/AD602 output impedance is 50 Ω and offers low distortion, low noise and wide bandwidth.

AD5231/AD5232/AD5233 are nonvolatile memory digital potentiometers that maintain the wiper settings. They provide single-, dual-, and quad-channel programmable resistors with different resolutions and terminal resistances. This product can be used as a replacement for mechanical potentiometers for applications such as gain and offset adjustment, programmable voltage to current conversion, programmable filters, delays, time constants, etc.