ANALOG Manuals

The ADG736L is a low voltage 2.5Ω dual SPDT switch produced by Analog Devices. It is suitable for USB 1.1 signal switching circuits, mobile phones, PDAs, battery-powered systems, communication systems, sample-and-hold systems, audio signal routing, audio and video switching, and mechanical reed relay replacement.

The SSM2402/SSM2412 are dual analog switches designed specifically for high performance audio applications. Distortion and noise are negligible over the full audio operating range of 20 Hz to 20 kHz at signal levels of up to 10 V rms. The SSM2402/SSM2412 offer a monolithic integrated alternative to expensive and noisy relays or complex discrete JFET circuits. Unlike conventional general-purpose CMOS switches, the SSM2402/SSM2412 provide superb fidelity without audio “clicks” during switching. Conventional TTL or CMOS logic can be used to control the switch state. No external components are required.

The document describes the features and characteristics of Analog Devices' TigerSHARC and Blackfin Embedded Processor ADSP-BF536/ADSP-BF537.

This document describes the features and characteristics of ADuC831, including 8-channel 12-bit ADC, dual 12-bit voltage output DACs, on-chip temperature sensor, and voltage reference. The product also features 62KB flash/EE program memory, 4KB flash/EE data memory, and 2304 bytes of data RAM. It utilizes an 8051 core with support for various peripheral interfaces and power modes. It is suitable for applications such as laser power control in optical networking.

The AD603 is a low noise, voltage-controlled amplifier for use in RF and IF AGC systems. It provides accurate, pin selectable gains of –11 dB to +31 dB with a bandwidth of 90 MHz or 9 dB to 51 dB with a bandwidth of 9 MHz. Any intermediate gain range may be arranged using one external resistor. The input referred noise spectral density is only 1.3 nV/√Hz and power con- sumption is 125 mW at the recommended ±5 V supplies. The decibel gain is “linear in dB,” accurately calibrated, and stable over temperature and supply. The gain is controlled at a high impedance (50 MΩ), low bias (200 nA) differential inp

The AD1865 is a complete, dual 18-bit digital-to-analog converter (DAC) offering excellent THD+N and SNR performance while requiring no external components. It includes two complete signal channels, providing cophased voltage or current output signals and eliminating the need for output components.

The AD1892 is a complete EIAJ CP-340 (CP-1201), IEC-958, AES/EBU, S/PDIF compatible digital audio receiver and asynchronous sample rate converter. It features status pins and microprocessor interfaces for stand-alone and microcontroller-oriented operation. The product also integrates a channel status buffer and Q-channel subcode buffer, supporting EIAJ CP-2401. With a 20-bit SamplePort® architecture, it provides superb jitter rejection on the input port. The sample rate conversion ranges from 8 kHz to 48 kHz with a 1:5 upsampling range and a 1:0.85 downsampling range. It offers a dynamic range of 120 dB and -113 dB THD+N @ 1 kHz. Additionally, it includes features such as CRC calculation, a four-wire SPI™ compatible serial control port, mute input pin, power-down mode, single +5 V supply, flexible three-wire serial data port with multiple modes (left-justified, right-justified, and I2S-compatible). The AD1892 is widely used in DVD, DAT, MD, DCC, and CD-R recorders and players, computer multimedia products, DAB receivers, and automotive digital audio networks.

AD9980 is a high-performance 8-bit display interface with a maximum conversion rate of 95 MSPS, automated offset adjustment, various output format modes, etc.

The ADP3000 is a high-frequency switching regulator from Analog Devices. It features low power consumption, wide input voltage range, adjustable output voltage, and few external components. It is mainly used in notebook computers, palmtop computers, cellular phones, hard disk drives, portable instruments, pagers, etc.

This application note discusses the effects of clock phase noise and jitter on sampled systems and recommends considering system performance and cost when selecting clock circuits.

The AD8628/AD8629/AD8630 are wide bandwidth auto-zero amplifiers featuring rail-to-rail input and output swing and low noise.

AD1881A is an audio codec device that supports the AC'97 2.1 standard. It integrates 16-bit analog/digital converters and digital/analog converters, as well as audio input and output interfaces.

AD202/AD204 is a low-cost, miniature isolation amplifier with small size, low power consumption, high accuracy, high CMR, wide bandwidth, high CMV isolation, etc., which can be used in various applications such as multi-channel data acquisition, current shunt measurement, motor control, process signal isolation, high-voltage instrumentation amplifier, etc.

The ADXL202EB is a simple evaluation board that allows the user to quickly evaluate the performance of the ADXL202 dual axis ±2 g accelerometer. Only three additional through-hole passive components must be added, depending on the bandwidth required in your application.

The 7B47 is a thermocouple input module produced by Analog Devices. It can interface, amplify and filter input voltages from a J, K, T, E, R, S, B or N-type thermocouple and output a linear output voltage of either +1 V to +5 V or 0 V to +10 V. All 7B47 series modules are mix-and-match and hot swappable.