Panasonic DMC-FT20 / DMC-TS20 series Error Codes

41 codes from pages 23–24 of the manual

This is the list of error codes the Panasonic manual gives for the DMC-FT20 / DMC-TS20 series digital camera. Find your code below and open it for what the manual says about its causes and what to do.

Error codes from p. 23

CodeWhat it meansPage
1800 PSD (X) error: Hall element (X axis) position detect error in OIS unit. p. 23
2000 PSD (Y) error: Hall element (Y axis) position detect error in OIS unit. p. 23
3000 GYRO (X) error: Gyro (IC7101) detect error on Main P.C.B. p. 23
4000 GYRO (Y) error: Gyro (IC7101) detect error on Main P.C.B. (Gyro element) or IC6001 (VENUS ENGINE) p. 23
5000 MREF error (Reference voltage error). p. 23
6000 Drive voltage (X) error. LENS Unit, LENS flex breaks, IC6001(VENUS ENGINE) AD value error, etc. p. 23
7000 Drive voltage (Y) error. LENS Unit, LENS flex breaks, IC6001(VENUS ENGINE) AD value error, etc. p. 23
0710 Collapsible barrel Low detect error (Collapsible barrel encoder always detects Low.) Mechanical lock, FP9003-(2) signal line or IC6001 (VENUS ENGINE) p. 23
0720 Collapsible barrel High detect error (Collapsible barrel encoder always detects High.) Mechanical lock, FP9003-(2) signal line or IC6001 (VENUS ENGINE) p. 23
0760 The zoom position jump is detected due to the impact (i.e. drop.) to the camera occurs. p. 23
0701 HP High detect error (Focus encoder always detects High, and not becomes Low) Mechanical lock, FP9003-(40) signal line or IC6001 (VENUS ENGINE) p. 23
0702 HP Low detect error (Focus encoder always detects Low, and not becomes High) Mechanical lock, FP9002-(40) signal line or IC6001 (VENUS ENGINE) p. 23
0000 Power ON time out error. p. 23
8000 OIS adj. Yaw direction off set error p. 23
9000 OIS adj. Pitch direction off set error p. 23
A000 OIS adj. Yaw direction gain error p. 23
B000 OIS adj. Pitch direction gain error p. 23
C000 OIS adj. Yaw direction position sensor error p. 23
D000 OIS adj. Pitch direction position sensor error p. 23
E000 OIS adj. other error p. 23
28'0 Flash charging error. p. 24
0001 EEPROM read error p. 24
0003 EEPROM write error p. 24
0005 Firmware version up error p. 24
0008 SDRAM error p. 24
0009 SDRAM Mounting defective p. 24
2C'0 SYSTEM IC Initialize failure error p. 24
30'0 NMI reset p. 24
31'0 Card logic error p. 24
0002 Card physical error p. 24
0004 Write error p. 24
39'0 Format error p. 24
38'0 Camera task invalid code error. p. 24
0100 File time out error in recording motion image p. 24
0200 File data cue send error in recording motion image p. 24
0300 Single or burst recording brake time out. p. 24
3B'0 FLASHROM processing early period of camera during movement. p. 24
3C'0 Imperfect zoom lens processing p. 24
35'0 Software error (0-7bit : command, 8-15bit : status) p. 24
35*1 Though record preprocessing is necessary, it is not called. p. 24
35*2 Though record preprocessing is necessary, it is not completed. p. 24

Codes and descriptions are taken from the manufacturer’s manual; page numbers link to the PDF. ManualLib is not affiliated with Panasonic. Found a mistake? Report an error.