Industrial

The AD5171 is a 64-position, one-time programmable (OTP) digital potentiometer that uses fuse link technology to achieve memory retention of resistance setting function. OTP is a cost-effective alternative over the EEMEM approach for users who do not need to reprogram new memory setting in the digital potentiometer. This device performs the same electronic adjustment function like most mechanical trimmers and variable resistors.

The 256-position Two-Time Programmable I2C Digital Potentiometer AD5170 Rev. A is an integrated miniature potentiometer that uses I2C communications, features 256 positions, double-time programmable, set-and-forget, free adjustment, and low power consumption.

The CENTRAL SEMICONDUCTOR CMHZ4099 Series types are high quality Silicon Zener Diodes designed for low leakage, low current and low noise applications.

The CM1690 is a family of pi-style EMI filter arrays with ESD protection from CMD. The product integrates four, six and eight filters (C-L-C) in small form factor uDFN 0.40mm pitch packages. Each EMI filter channel of the CM1690 is implemented as a 3-pole L-C filter where the component values are 16pF-12nH-16pF. The CM1690's roll-off frequency at –6dB attenuation is 330MHz and can be used in applications where the data rates are as high as 140Mbps while providing greater than –35dB attenuation.

The AD5170 is a 256-position two-time programmable I2C digital potentiometer, which offers four end-to-end resistance selections of 2.5 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ.

The AD5165 is a 256-position digital potentiometer with ultralow standby current, 1.8V logic high voltage, and 2.7-5.5V supply voltage.

This document provides instructions for the use of the CT-100 Active Rough Vacuum Gauge from Vacuum Technologies. It includes warranty information and precautions.

This document provides installation instructions and application information for the Edwards ATC and APG to Varian CT-100 Pin Adapter. It also explains the differences between the CT-100 and Edwards gauges.

This document provides instructions on how to replace the VS Ion Source Board, as well as the warranty terms and limitations of the product.

The AD5162 is a 2-channel 256-position SPI digital potentiometer with 2.5 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ resistance values. It is available in the MSOP-10 package, has low power consumption, and a wide operating voltage range. It is suitable for applications such as system calibration, electronic level setting, mechanical trimmer replacement, permanent factory PCB setting, transducer adjustment, RF amplifier biasing, and automotive electronics adjustment.

AD515A is a monolithic FET-input operational amplifier with a guaranteed maximum input bias current of 75 fA (AD515AL). The AD515A is a monolithic successor to the industry standard AD515 electrometer, and will replace the AD515 in most applications. The AD515A also delivers laser-trimmed offset voltage, low drift, low noise and low power, a combination of features not previously available in ultralow bias current circuits. All devices are internally compensated, protected against latch-up and are short circuit protected. The AD515A is typically used for sensor and instrumentation measurement, ohmmeter, divider, voltage reference, DC voltage measurement and current sensor applications. The AD515A can be used to measure small currents or voltages from high impedance resistors or capacitors.

The AD5100 is a system management IC with programmable quad voltage monitoring and supervisory functions. It features two high voltage (30V) monitoring inputs and two low voltage (5V) monitoring inputs, with programmable thresholds, delays, and warning functions. Additionally, it includes supervisory functions such as watchdog reset with programmable timeout, failed processor watchdog enabled shutdown, selectable floating watchdog reset function, and manual reset. The IC also has a digital interface and programmability using an I2C compatible interface.

This product is a precision monolithic operational amplifier with high accuracy and fast settling time.

AD5040/AD5060 are single 14/16-bit buffered voltage output DACs from the nanoDAC family. They operate at 3V/5V and come in an 8-pin SOT23 package. They feature a low power serial interface, fast settling, and low power operation.