Industrial

TSV321-TSV358-TSV324 are general purpose input/output rail-to-rail low power operational amplifiers. They operate with voltages ranging from 2.5V to 6V and feature both I/O rail-to-rail. These amplifiers are suitable for battery-powered applications, audio drivers, sensor signal conditioning, and laptop/notebook computers.

The TL16C750 is a TL16C450-compatible asynchronous communications element with programmable 16- or 64-byte FIFOs and autoflow control

TL16C554A, TL16C554AI Asynchronous-Communications Element SLLS509A-AUGUST 2001-REVISED JULY 2003 1 POST OFFICE BOX 655303•DALLAS, TEXAS 75265 �Integrated Asynchronous-Communications Element �Consists of Four Improved TL16C550C ACEs Plus Steering Logic �In FIFO Mode, Each ACE Transmitter and Receiver Is Buffered With 16-Byte FIFO to Reduce the Number of Interrupts to CPU �In TL16C450 Mode, Hold and Shift Registers Eliminate Need for Precise Synchronization Between the CPU and Serial Data �Up to 16-MHz Clock Rate for up to 1-Mbaud Operation �Programmable Baud-Rate Generators Which Allow Division of Any Input Reference Clock by 1 to (216–1) and Generate an Internal 16 × Clock �Adds or Deletes Standard Asynchronous Communication Bits (Start, Stop, and Parity) to or From the Serial-Data Stream �Independently Controlled Transmit, Receive, Line Status, and Data Set Interrupts �5-V and 3.3-V Operation �Fully Programmable Serial Interface Characteristics: – 5-, 6-, 7-, or 8-Bit Characters – Even-, Odd-, or No-Parity Bit – 1-, 1 1/2-, or 2-Stop Bit Generation – Baud Generation (DC to 1-Mbit Per Second) �False Start Bit Detection �Complete Status Reporting Capabilities �Line Break Generation and Detection �Internal Diagnostic Capabilities: – Loopback Controls for Communications Link Fault Isolation – Break, Parity, Overrun, Framing Error Simulation �Fully Prioritized Interrupt System Controls �Modem Control Functions (CTS, RTS, DSR, DTR, RI, and DCD) �3-State Outp

TL16C554, TL16C554I ASYNCHRONOUS COMMUNICATIONS ELEMENT SLLS165D – JANUARY 1994 – REVISED JULY 1998

TEA6420 is a bus-controlled audio matrix switch chip with 5 stereo inputs and 4 stereo outputs. All the switching possibilities are changed through the I2C bus. It has gain control of 0/2/4/6dB/mute for each output, can be cascaded (2 different addresses), and is controlled via serial bus. It has very low noise and distortion.

This document describes the features and characteristics of the TEA6425 video cellular matrix, including 6 video inputs and 8 video outputs, selectable 0.5dB or 6.5dB gain for each output, high impedance switch for each output, programmable clamp mode for each input, -60dB crosstalk, etc.

The TEA6422 is a 6-channel audio matrix switch with low noise, low distortion, full ESD protection, and wide audio dynamic range (3 VRMS).

The TSL1014 is a 14+1 channel buffer used to buffer the reference voltage for gamma correction in thin film transistor (TFT) liquid crystal displays (LCD).

The STVM100 is a programmable VCOM adjustment solution for thin-film transistor (TFT) liquid-crystal displays (LCDs) to remove “flickers”. It is also used in e-paper and e-book applications to avoid the 'ghosting' effect (residual pixels after display refresh). It can replace a mechanical potentiometer, so that the factory operator can physically view the front screen when performing the VCOM adjustment. This significantly reduces labor costs, increases reliability, and enables automation. The STVM100 provides a digital I2C interface to control the sink current output (IOUT). This output drives an external resistive voltage divider, which can then be applied to an external VCOM buffer. Three external resistors R1, R2, and RSET determine the highest and lowest value of the VCOM. An increase in the output sink current will lower the voltage.

TSL1018 is an 18+1 channel buffer used to buffer the reference voltage for gamma correction in TFT liquid crystal displays (LCD). It features wide supply voltage range, low operating current, high output current, and industrial temperature range.

STV7733 is a high-voltage, row/column driver IC with 320 tri-level (high-voltage, medium voltage and ground) power outputs. It can operate at 90V and supports logic supply range of 2.5V to 3.3V. It is suitable for COG, COF and TCP solutions.

The STV7622 is a data driver for Plasma Display Panels (PDP) designed in the ST’s proprietary BCD high-voltage technology. It controls up to 192 outputs via an input data bus (3, 6 or 2 × 3-bits wide) operating at up to 60MHz. This large number of outputs reduces the number of connections between the controller board and the data driver ICs. The STV7622 contains a new logic input stage that minimizes EMI resulting from the transmission of high speed TTL or LVCMOS data and clock signals. This new input stage is RSDS compliant. It enables increasing the operating frequency without compromising noise immunity. The input data bus is configured by dedicated input pins.

The STV7623 is a 1-bit x 480 shift register with dual rail high voltage/medium current output, with global blank and polarity control. The maximum shift frequency starts from 1 MHz for a 1.8 V type input signal, up to 10 MHz for a 3.3 V type input signal. This generic device can be used for segmented/dot matrix electroluminescent displays to drive an array of organic electronic transistors, or for technologies related to e-Paper/e-Reader/digital signage solutions. The device can be daisy-chained for various display resolutions.

The TL16C552A, TL16C552AM is a dual asynchronous communications element with FIFO function from Texas Instruments, which can operate at a clock rate of 16Mhz and support a transmission speed of 1Mbaud. The product has the following features: IBM PC/AT compatible, two TL16C550 ACEs, enhanced bidirectional printer port, 16-byte FIFO, reduced CPU interrupts, independently controlled transmit, receive, line status and data set interrupts for each channel, individual modem control signals for each channel, programmable serial interface characteristics for each channel, 5-, 6-, 7- or 8-bit characters, even, odd or no parity bit generation and detection, 1-, 1-1/2- or 2 stop bit generation, TTL drive for the I/O and control bus for each channel, hardware and software compatible with TL16C452