Industrial

This datasheet is for STGIPN3H60A, a 3 A - 600 V 3-phase IGBT inverter bridge with low EMI, VCE(sat) negative temperature coefficient, 3.3 V, 5 V, 15 V CMOS/TTL input comparators with hysteresis and pull-down resistor, Undervoltage lockout, Internal bootstrap diode, Interlocking function

This document provides preliminary information on a new product, including its features and characteristics.

This document describes the features and characteristics of the SPAC265-8W AC-DC power supply module, including open frame switch mode power supply, European input voltage range, single output 5V, 8W peak power, 4W continuous operating mode, etc.

TL16C550C/ TL16C550CI is an asynchronous communications element with autoflow control.

The L2293Q is a monolithic integrated high voltage, high current four channel driver designed to accept standard DTL or TTL logic levels and drive inductive loads (such as relays solenoides, DC and stepping motors) and switching power transistors.

The L6229Q is a ST's three-phase brushless DC motor driver with overcurrent protection. The device is fabricated in BCD multipower technology, combining isolated DMOS power transistors, CMOS and bipolar circuits on the same chip. The device includes all the circuitry needed to drive a three-phase BLDC motor including: a three-phase DMOS bridge, a constant off time PWM current controller and the decoding logic for single ended hall sensors that generates the required sequence for the power stage. The device is available in VFQFPN-32 5 x 5 package, featuring a non-dissipative overcurrent protection on the high side power MOSFETs and thermal shutdown.

The L6470 is a fully integrated microstepping motor driver with motion engine and SPI interface, suitable for driving two-phase bipolar stepper motors.

SPIMD20 is an integrated motor drive with real time connectivity enabling brushless motor manufacturers to create a proprietary motion control system based on a general purpose brick.

This document introduces the L6460 SPI configurable stepper and DC multi motor driver, which features operating supply voltage from 13V to 38V, 4 full bridge driver configurable for multi-motor application to drive 2 DC and 1 stepper motor or 4 DC motor.

The L6230 is a DMOS fully integrated three-phase motor driver with overcurrent protection, optimized for FOC application thanks to the independent current senses

The L6208Q is a DMOS fully integrated stepper motor driver with non-dissipative overcurrent protection, realized in BCDmultipower technology, which combines isolated DMOS power transistors with CMOS and bipolar circuits on the same chip. The device includes all the circuitry needed to drive a two-phase bipolar stepper motor including: a dual DMOS full bridge, the constant OFF time PWM current controller that performs the chopping regulation, and the phase sequence generator that generates the stepping sequence. Available in QFN48 7x7 package, the L6208Q features a non-dissipative overcurrent protection on the high-side Power MOSFETs and thermal shutdown.

The L6207Q is a DMOS dual full bridge driver designed for motor control applications. It operates from 8 to 52V supply voltage and has a 5.6A output peak current. The RDS(on) value is 0.3Ω at 25°C. It can operate at frequencies up to 100kHz. The device includes two independent constant OFF time PWM current controllers for chopping regulation. It also features thermal shutdown and non-dissipative overcurrent protection.

TL16C550B, TL16C550BI Asynchronous Communications Element is capable of running with all existing TL16C450 software and after reset, all registers are identical to the TL16C450 register set.

The L6235Q is a DMOS fully integrated 3-phase motor driver with overcurrent protection. Realized in BCDmultipower technology, the device combines isolated DMOS power transistors with CMOS and bipolar circuits on the same chip. The device includes all the circuitry needed to drive a 3-phase BLDC motor including: a 3-phase DMOS bridge, a constant OFF time PWM current controller and the decoding logic for single ended Hall sensors that generates the required sequence for the power stage. Available in QFN48 7x7 package, the L6235Q features a non-dissipative overcurrent protection on the high-side power MOSFETs and thermal shutdown.