Industrial

This datasheet provides the characteristics of the 1N5221B to 1N5267B small signal zener diodes. These diodes have a standard ±5% zener voltage tolerance and are available in a DO35 glass case.

1N4728A to 1N4764A are silicon planar power Zener diodes manufactured by Vishay Semiconductors. They are used in stabilizing and clipping circuits with high power rating.

CS1680 is a dot matrix LCD driver circuit with 80 drive channels, which can be used as a segment driver.

The HIN202, HIN206, HIN207, HIN208, HIN211, HIN213 are a family of +5V powered RS-232 transmitters/receivers with 0.1 microfarad external capacitors. This family of RS-232 transmitters/receivers interface circuits meet all ElA RS-232E and V.28 specifications, and are particularly suited for those applications where ±12V is not available. They require a single +5V power supply and feature onboard charge pump voltage converters which generate +10V and -10V supplies from the 5V supply. The family of devices offers a wide variety of RS-232 transmitter/receiver combinations to accommodate various applications (see Selection Table). The HIN206, HIN211 and HIN213 feature a low power shutdown mode to conserve energy in battery powered applications. In addition, the HIN213 provides two active receivers in shutdown mode allowing for easy “wakeup” capability. The drivers feature true TTL/CMOS input compatibility, slew rate-limited output, and 300Ω power-off source impedance. The receivers can handle up to ±30V input, and have a 3kΩ to 7kΩ input impedance. The receivers also feature hysteresis to greatly improve noise rejection.

The HI-546, HI-547, HI-548, and HI-549 are analog multiplexers with active overvoltage protection and guaranteed rON matching. These devices allow analog input levels to exceed the power supply without damage or signal path disturbance. They feature active protection circuitry to maintain signal fidelity even under fault conditions. The analog inputs can withstand constant 70VP-P levels with ±15V supplies, while the digital inputs can sustain continuous faults up to 4V greater than either supply. The devices also provide protection against short-circuiting in case of multiplexer supply loss. The HI-546 is a single 16-channel device, the HI-547 is an 8-channel differential device, the HI-548 is a single 8-channel device, and the HI-549 is a 4-channel differential device. These devices are suitable for systems where the analog inputs come from external equipment or separately powered circuitry. They are fabricated with 44V Dielectrically Isolated CMOS technology. The HI-506/507/508/509 multiplexers are recommended for applications that do not require input overvoltage protection. For more information, refer to Application Notes AN520 and AN521. MIL-STD-883 compliant parts are available upon request for the HI-546/883.

This datasheet introduces the HI5660 8-bit, 125MSPS, high speed D/A converter's features.

This document describes the features and characteristics of the ALD4211/ALD4212/ALD4213 quad CMOS analog switches, which are designed for ultra low charge injection applications using a single 3V to 12V power source. In the high precision mode, the input signals are connected to COM input pins and the analog switch outputs are the OUT pins. In this connection configuration, a very low charge injection of 0.2pC is achieved when sampling capacitors of 200pF are used. In the general purpose application mode, the COM and the OUT terminals can be reversed, if necessary. The input signals, in this case, are connected to either the COM or the OUT terminals. The outputs of the analog switches are then the OUT or the COM terminals, corresponding to the other terminal of the analog switches.

ALD172xE is the world's first single-chip CMOS operational amplifier with adjustable voltage bias on the integrated circuit. It can adjust the voltage bias according to the application scenario, achieve zero bias, and at the same time have the advantages of high precision, high gain and high output voltage range, which is very suitable for use in various occasions with harsh voltage bias requirements.

ALD1108E/ALD1110E is a new type of circuit regulator product launched by Advanced Linear Devices. It is based on CMOS MOSFET devices with precise voltage adjustment characteristics. When used in combination with ALD E100 EPAD programmer and adapter module, the product can precisely adjust the circuit and support 20,000 steps.

The LZ2523 is a 1/5-type (3.6 mm) solid-state image sensor that consists of PN photo-diodes and CCDs (charge-coupled devices). With approximately 320 000 pixels (542 horizontal x 582 vertical), the sensor provides a stable high-resolution color image.

The LZ2513 is a 1/5-type (3.6 mm) solid-state image sensor that consists of PN photo-diodes and CCDs (charge-coupled devices). With approximately 270 000 pixels (542 horizontal x 492 vertical), the sensor provides a stable high-resolution color image.

The LZ24BP is a 1/4-type (4.5 mm) solid-state image sensor that consists of PN photo-diodes and CCDs. It has approximately 350,000 pixels and provides a stable high-resolution color image. It features progressive scan, square pixel, and is compatible with VGA format.