RICOH Manuals

The RP101x Series are CMOS-based voltage regulator ICs with high output voltage accuracy, extremely low supply current, low ON-resistance, and high ripple rejection.

The RP101x Series are CMOS-based LDO regulators featuring 300mA output. RP101x has the supply current as low as 18μA, which is far lower than current products. Due to a built-in transistor with low on-resistance of 0.87Ω (at VOUT=2.8V) , RP101x provides a low dropout voltage. RP101x also has an excellent line transient response, 75dB ripple rejection, and low noise. The output voltage accuracy has been improved to ± 0.6% and the temperature drift coefficient of the output voltage is as low as ± 30ppm/°C.

R1191x series 300mA LDO regulator with the reverse current protection. The maximum operating voltage is 16V. These ICs can switch to the fast mode and the low power mode by the low power / fast mode changer pin (ECO pin) without changing the output voltage value.

The R1191x Series are CMOS-based manual mode switching 16V input voltage regulators with ECO pin featuring 300mA output. By inputting control signals to the ECO pin, the mode of the regulator can be switched to low power mode or fast response mode, thus making both active and sleep modes available for the system. The built-in reverse current protection circuit prevents the current flow from VOUT to VDD when VOUT is higher than VDD. This feature makes the product ideally suited for backup circuit. Standby mode and auto-discharge function are also available (see Selection Guide). Ceramic capacitors can be used.

R1161x Series are CMOS-based voltage regulator ICs with high output voltage accuracy, low supply current, and low ON-resistance. Each of these voltage regulator ICs consists of a voltage reference unit, an error amplifier, resistors for setting output voltage, a current limit circuit, and a chip enable circuit. These ICs perform with low dropout voltage and a chip enable function. To prevent the destruction by over current, current limit circuit is included. The R1161x Series have 3-mode. One is standby mode with CE or standby control pin. Standby mode realizes ultra small consumption current off mode. Other two modes are realized with ECO pin. Fast Transient Mode (FT mode) and Low Power Mode (LP mode) are alternative with ECO pin. Consumption current is reduced at Low Power Mode compared with Fast Transient Mode. Output voltage is maintained between FT mode and LP mode. The output voltage of these ICs is internally fixed with high accuracy. Since the packages for these ICs are SOT-23-5, SON-6 (Limited), and HSON-6 (Limited), high density mounting of the ICs on boards is possible.

The R1161N Series are CMOS-based manual mode switching LDO regulators with ECO pin featuring 300mA output. By inputting control signals to the ECO pin, the mode of the regulator can be switched to low power mode or fast response mode, thus making both active and sleep modes available for the system. The CE pin can switch the regulator into standby mode.

The R1131x series are CMOS-based low voltage regulator ICs with output voltage range from 0.8V to 3.3V. The minimum operating voltage is 1.4V.

The R1131N Series is a CMOS-based LDO regulator with a 300mA output. The input voltage (VIN) can go as low as 1.4V and the output voltage can be set as low as 0.8V. The CE pin allows the regulator to switch into standby mode. Ceramic capacitors can be used. Features include low supply current, low standby current, low dropout voltage, and good ripple rejection.

The R1130x Series are CMOS-based voltage regulator (VR) ICs. VR function has features of high ripple rejection, low dropout voltage, high output voltage accuracy, and ultra-low supply current.

The R1130H Series is a CMOS-based LDO regulator with a 300mA output. The input voltage (VIN) can go as high as 8V (maximum rating of 9V). R1130H is available in two versions: the internally fixed output voltage type or the adjustable output voltage type using an external resistor. The CE pin can switch the regulator into standby mode.

R1160x SERIES 3-MODE 200mA LDO REGULATOR is a low power, low dropout voltage, high accuracy LDO chip from ROHM, which has 3 working modes and can be switched between Fast Transient Mode (FT mode) and Low Power Mode (LP mode) by ECO pin.

The R1160N Series are CMOS-based Manual mode switching LDO regulators with ECO pin featuring 200mA output. By inputting control signals to the ECO pin, the mode of the regulator can be switched to low power mode or fast response mode, thus making both active and sleep modes available for the system. The CE pin can switch the regulator into standby mode. This feature helps to extend the battery life. Features include supply current, standby current, dropout voltage, ripple rejection, input voltage range, output voltage range, output voltage accuracy, temperature coefficient, etc.

The RP100x Series are CMOS-based low-dropout linear regulators with high output voltage accuracy, extremely low supply current, low ON-resistance, and high ripple rejection.

The RP107x Series are CMOS-based LDO regulators featuring 200mA output. Since the output capacitor and noise bypass capacitor are able to be reduced and the packages are small DFN(PLP)1212-6, WLCSP-4-P5, and SC-88A, high density mounting on boards are possible. The input voltage (VIN) is as low as Min.1.4V and the output voltage can be set from 1.0V. Supply current is as low as 9.5μA compared to existing lines. The CE pin can switch the regulator to standby mode.

The RP107x Series are CMOS-based LDO regulators featuring 200mA output