National Semiconductor manuals, page 52
NATIONAL SEMICONDUCTOR ADC78H89 Manual
The ADC78H89 is a low-power, seven-channel CMOS 12-bit analog-to-digital converter with a conversion throughput of 500 KSPS.
National Semiconductor DS90LV048A 3V LVDS Quad CMOS Differential Line Receiver handbook
DS90LV048A 3V LVDS Quad CMOS Differential Line Receiver is a quad CMOS flow-through differential line receiver designed for applications requiring ultra low power dissipation and high data rates.
National Semiconductor LMH6504 Wideband Low Power Variable Gain Amplifier datasheet
The LMH6504 is a wideband, low power, variable gain amplifier from Texas Instruments. Its maximum gain is 80 dB, bandwidth is 10 MHz, and it can directly drive low impedance loads.
NATIONAL SEMICONDUCTOR - ADC081S021 Single Channel 50 to 200 ksps 8-Bit A/D Converter handbook
The ADC081S021 is a low-power, single channel CMOS 8-bit analog-to-digital converter with a high-speed serial interface. Unlike the conventional practice of specifying performance at a single sample rate only, the ADC081S021 is fully specified over a sample rate range of 50 ksps to 200 ksps. The converter is based upon a successive-approximation register architecture with an internal track-and-hold circuit. The output serial data is straight binary, and is compatible with several standards, such as SPI™, QSPI™, MICROWIRE, and many common DSP serial interfaces. The ADC081S021 operates with a single supply that can range from +2.7V to +5.25V. Normal power consumption using a +3.6V or +5.25V supply is 1.3 mW and 7.7 mW, respectively. The power-down feature reduces the power consumption to as low as 2.6 µW using a +5.25V supply. The ADC081S021 is packaged in 6-lead LLP and SOT-23 packages. Operation over the industrial temperature range of −40˚C to +85˚C is guaranteed.
NATIONAL SEMICONDUCTOR LM628/LM629 Manual
The LM628/LM629 are dedicated motion-control processors designed for use with a variety of DC and brushless DC servo motors, and other servomechanisms which provide a quadrature incremental position feedback signal.
NATIONAL SEMICONDUCTOR LM628/LM629 Precision Motion Controller
National Semiconductor LMV321/LMV358/LMV324 Single/Dual/Quad General Purpose Low Voltage Rail-to-Rail Output Operational Amplifiers handbook
NATIONAL SEMICONDUCTOR LMV321/LMV358/LMV324 Single/Dual/Quad General Purpose Low Voltage Rail-to-Rail Output Operational Amplifiers datasheet
LMV321/LMV358/LMV324 Single/Dual/Quad General Purpose, Low Voltage, Rail-to-Rail Output Operational Amplifiers
National LP38691/LP38693 500mA Low Dropout CMOS Linear Regulators Stable with Ceramic Output Capacitors handbook
NATIONAL SEMICONDUCTOR LM27313 1.6 MHz Boost Converter With 30V Internal FET Switch in SOT-23 handbook
The LM27313 is a 1.6MHz current-mode boost converter with an internal 30V FET switch, packaged in SOT-23, featuring extremely high power density. It is ideal for boosting voltages to 5V-28V.
NATIONAL SEMICONDUCTOR LM2585 SIMPLE SWITCHER 3A Flyback Regulator handbook
LM2585 is a 3A flyback regulator
NATIONAL SEMICONDUCTOR LM5104 High Voltage Half-Bridge Gate Driver with Adaptive Delay handbook
LM5104 High Voltage Half-Bridge Gate Driver with Adaptive Delay
National LM20 2.4V 10 A SC70 micro SMD Temperature Sensor handbook
LM20 is a precision analog output CMOS integrated circuit temperature sensor that operates over a −55˚C to +130˚C temperature range.
NATIONAL SEMICONDUCTOR - LM2662/LM2663 Switched Capacitor Voltage Converter handbook
The LM2662/LM2663 CMOS charge-pump voltage converter inverts a positive voltage in the range of 1.5V to 5.5V to the corresponding negative voltage. The LM2662/LM2663 uses two low cost capacitors to provide 200 mA of output current without the cost, size, and EMI related to inductor based converters. With an operating current of only 300 µA and operating efficiency greater than 90% at most loads, the LM2662/LM2663 provides ideal performance for battery powered systems. The LM2662/LM2663 may also be used as a positive voltage doubler. The oscillator frequency can be lowered by adding an external capacitor to the OSC pin. Also, the OSC pin may be used to drive the LM2662/LM2663 with an external clock. For LM2662, a frequency control (FC) pin selects the oscillator frequency of 20 kHz or 150 kHz. For LM2663, an external shutdown (SD) pin replaces the FC pin. The SD pin can be used to disable the device and reduce the quiescent current to 10 µA. The oscillator frequency for LM2663 is 150 kHz.
National Semiconductor LM4665 Filterless High Efficiency 1W Switching Audio Amplifier handbook