Maxim manuals, page 39
MAXIM MAX9268 Manual
The MAX9268 deserializer utilizes Maxim’s gigabit multimedia serial link (GMSL) technology. It features an LVDS system interface for reduced pin count and a smaller package, and pairs with any GMSL serializer to form a complete digital serial link for joint transmission of high-speed video, audio, and bidirectional control data.
MAXIM MAX9270 handbook
The MAX9270 deserializer uses Maxim's gigabit multimedia serial link (GMSL) technology. The device functions the same as the MAX9260 deserializer without an output enable (ENABLE) pin. Outputs are enabled or disabled by a register bit. The deserializer pairs with any GMSL serializer to form a complete digital serial link for joint transmission of high-speed video, audio, and control data. The deserializer accepts a maximum serial payload data rate of 2.5Gbps for a 15m shielded twisted-pair (STP) cable. The 24-bit or 32-bit width parallel interface operates up to a maximum bus clock of 104MHz or 78MHz, respectively. This serial link supports display panels from QVGA (320 x 240) up to XGA (1280 x 768), or dual-view WVGA (2 x 854 x 480). The 24-bit or 32-bit mode handles 21 or 29 bits of data, along with an I2S input, supporting 4- to 32-bit audio word lengths and an 8kHz to 192kHz sample rate. The embedded control channel forms a full-duplex, differential 100kbps to 1Mbps UART link between the serializer and deserializer. The host electronic control unit (E
MAXIM MAX5406 handbook
The MAX5406 stereo audio processor provides a complete audio solution with volume, balance, bass, and treble controls. It features dual 32-tap logarithmic potentiometers for volume control, dual potentiometers for balance control, and linear digital potentiometers for tone control. A simple debounced pushbutton interface controls all functions. The MAX5406 advances the wiper setting once per button push. Maxim’s proprietary SmartWiper™ control eliminates the need for a microcontroller (µC) to increase the wiper transition rate. Holding the control input low for more than 1s advances the wiper at a rate of 4Hz for 4s and 16Hz thereafter. An integrated click/pop suppression feature eliminates the audible noise generated by the wiper’s movements. The MAX5406 provides a subwoofer output that internally combines the left and right channels. An external filter capacitor allows for a customized cut-off frequency for the subwoofer output. A bass-boost mode enhances the low-frequency response of the left and right channels. An integrated bias amplifier generates the required (VDD + VSS) / 2 bias voltage, eliminating the need for external op amps for unipolar operation. The MAX5406 also features ambience control to enhance the separation of the left- and right-channel outputs for headphones and desktop speakers systems, and a pseudostereo feature that approximates stereo sound from a monophonic signal.
MAXIM MAX9257A/MAX9258A Manual
The MAX9257A/MAX9258A is a fully programmable serializer/deserializer with UART/I2C control channel
MAXIM MAX3355E handbook(1)
The MAX3355E is a USB OTG dual-role device from MAXIM that integrates a charge pump and comparators to enable a system with an integrated USB on-the-go (OTG) dual-role transceiver to function as a USB OTG dual-role device.
MAXIM MAX3353E Manual
The MAX3353E is an I2C-compatible USB On-the-Go (OTG) regulated charge pump with switchable pullup/pull- down resistors. It allows peripherals and mobile devices such as PDAs, cellular phones, and digital cameras to be interconnected without a host PC. The MAX3353E enables a system with an integrated USB dual-role transceiver to function as a USB OTG dual-role device. The charge pump in the MAX3353E supplies VBUS power and signaling that is required by the transceiver as defined in On-the-Go Supplement: USB 2.0, Revision 1.0. The MAX3353E provides the switchable pullup and pulldown resistors on D+ and D- required for a dual-role device. The MAX3353E integrates a regulated charge pump, switchable pullup/pulldown resistors, and an I2C-compatible 2-wire serial interface. The device provides a detector to monitor ID status and operates with logic supply voltages (VL) between +1.65V and VCC and charge-pump supply voltages (VCC) from +2.6V to +5.5V. The charge pump supplies an OTG-compatible output on VBUS while sourcing 8mA output current. The MAX3353E enables USB OTG communication between digital logic parts that cannot supply or tolerate the +5V VBUS levels that USB OTG requires. By control- ling and measuring VBUS using internal comparators, this device supports USB OTG session request protocol (SRP) and host negotiation protocol (HNP). The MAX3353E has built-in ±15kV ESD protection circuitry to guard VBUS, ID_IN, D+, and D-. The MAX3353E is available in a 5 x 4 chi.
MAXIM MAX3301E/MAX3302E handbook
The MAX3301E/MAX3302E fully integrated USB On-the-Go (OTG) transceivers and charge pumps allow mobile devices such as PDAs, cellular phones, and digital cameras to interface directly with USB peripherals and each other without the need of a host PC. Use the MAX3301E/MAX3302E with an embedded USB host to directly connect to peripherals such as printers or external hard drives. The MAX3301E/MAX3302E integrate a USB OTG transceiver, a VBUS charge pump, a linear regulator, and an I2C-compatible, 2-wire serial interface. An internal level shifter allows the MAX3301E/MAX3302E to interface with +1.65V to +3.6V logic supply voltages. The MAX3301E/MAX3302E’s OTG-compliant charge pump operates with +3V to +4.5V input supply voltages, and supplies an OTG-compatible output on VBUS while sourcing more than 8mA of output current. The MAX3301E/MAX3302E enable USB OTG communication from highly integrated digital devices that cannot supply or tolerate the +5V VBUS levels that USB OTG requires. The device supports USB OTG session-request protocol (SRP) and host-negotiation protocol (HNP). The MAX3301E/MAX3302E provide built-in ±15kV electrostatic-discharge (ESD) protection for the VBUS, ID_IN, D+, and D- terminals. The MAX3301E/MAX3302E are available in 25-bump chip-scale (UCSP™), 25-bump WLP package, 28-pin TQFN, and 32-pin TQFN packages and operate over the extended -40°C to +85°C temperature range.
MAXIM MAX5500/MAX5501 Manual
The MAX5500/MAX5501 is a four-channel low-power, 12-bit digital-to-analog converter (DAC) from Texas Instruments, with four precision output amplifiers in a small, 20-pin package. Each negative input of the four precision amplifiers is externally accessible providing flexibility in gain configurations, remote sensing, and high output drive capacity, making the MAX5500/MAX5501 ideal for industrial process control applications. Other features include software shutdown, hardware shutdown lockout, an active-low reset which clears all registers and DACs to zero, a user-programmable logic output, and a serial-data output. Each DAC provides a double-buffered input organized as an input register followed by a DAC register. A 16-bit serial word loads data into each input register. The serial interface is compatible with SPI™/QSPI™/ MICROWIRE™. The serial interface allows the input and DAC registers to be updated independently or simultaneously with a single software command. The 3-wire interface simultaneously updates the DAC registers. All logic inputs are TTL/CMOS-logic compatible. The MAX5500 operates from a single +5V power supply, and the MAX5501 operates from a single +3V power supply. The MAX5500/MAX5501 are specified over the extended -40°C to +105°C temperature range. Applications include industrial process controls, automatic test equipment, microprocessor (μP)-controlled systems, motion control, digital offset and gain adjustment, remote industrial controls. Features include four 12-bit DACs, four precision output amplifiers, external negative inputs, software shutdown, hardware shutdown lockout, low-level reset, user-programmable logic output, serial data output, etc.
MAXIM MAX3420E Manual
MAX3420E is a USB peripheral device from Microchip that complies with USB 2.0 specification. It contains the necessary digital logic and analog circuitry to implement a full-speed USB peripheral.
MAXIM MAX3421E Manual
The MAX3421E USB peripheral/host controller contains the digital logic and analog circuitry necessary to implement a full-speed USB peripheral or a full-/low- speed host compliant to USB specification rev 2.0.
MAXIM MAX5156/MAX5157 Manual
MAX5156/MAX5157 Low-Power, Dual, 12-Bit Voltage-Output DACs with Configurable Outputs
MAXIM MAX5104 Manual
The MAX5104 is a low-power, serial, voltage-output, dual 12-bit digital-to-analog converter (DAC) that consumes only 500µA from a single +5V supply. This device features Rail-to-Rail® output swing and is available in a space- saving 16-pin QSOP package. To maximize the dynamic range, the DAC output amplifiers are configured with an internal gain of +2V/V. The 3-wire serial interface is SPI™/QSPI™/MICROWIRE™ compatible. Each DAC has a double-buffered input organized as an input register followed by a DAC register, which allows the input and DAC registers to be updated independently or simultaneously with a 16-bit serial word. Additional features include programmable power- down (2µA), hardware power-down lockout (PDL), a separate reference voltage input for each DAC that accepts AC and DC signals, and an active-low clear input (CL) that resets all registers and DACs to zero. These devices provide a programmable logic pin for added functionality, and a serial-data output pin for daisy chaining.
MAXIM MAX3453E MAX3456E Manual
The MAX3453E-MAX3456E ±15kV ESD-protected USB-compliant transceivers interface low-voltage ASICs with USB devices. The devices fully comply with USB 1.1 and USB 2.0 when operating at full (12Mbps) and low (1.5Mbps) speeds. The MAX3453E-MAX3456E operate with VL as low as +1.65V, ensuring compatibility with low-voltage ASICs. The MAX3453E-MAX3456E feature a logic-selectable suspend mode that reduces current consumption to less than 40µA. Integrated ±15kV ESD protection protects the USB D+ and D- bidirectional bus connections. The MAX3453E supports only full-speed (12Mbps) operation. The MAX3453E/MAX3454E feature an internal 1.5kΩ USB pullup resistor and an enumeration function that allows devices to logically disconnect while plugged in. The MAX3453E/MAX3455E provide a push-pull bus-detect (BD) output that asserts high when VBUS > +4.0V. The MAX3453E-MAX3456E operate over the extended temperature range (-40°C to +85°C) and are available in 14-pin TSSOP and 16-pin (3mm x 3mm) thin QFN packages.
MAXIM MAX3344E/MAX3345E Manual(1)
The MAX3344E/MAX3345E USB transceivers convert logic-level signals to USB signals, and USB signals to logic-level signals. An internal 1.5kΩ USB pullup resistor supports full-speed (12Mbps) USB operation. The MAX3344E/MAX3345E provide built-in ±15kV ESD-protection circuitry on the USB I/O pins, D+ and D-, and VCC. The MAX3344E/MAX3345E operate with logic supply voltages as low as 1.65V, ensuring compatibility with low-voltage ASICs. The suspend mode lowers supply current to less than 40µA. An enumerate function allows devices to logically disconnect while plugged in. The MAX3344E/MAX3345E are fully compliant with USB specification 1.1, and full-speed operation under USB specification 2.0. The MAX3344E/MAX3345E have a USB detect that monitors the USB bus for insertion and signals this event. The MAX3344E USB_DET threshold is between 3.6V (min) and 4V (max), while the MAX3345E USB_DET threshold is between 1V (min) and 2.8V (max). The MAX3344E/MAX3345E are available in the miniature 4 ✕ 4 UCSP™, as well as the small 16-pin TSSOP, and are specified over the extended temperature range, -40°C to +85°C.
MAXIM MAX3346E Manual
The MAX3346E is a bidirectional transceiver that converts logic-level signals to USB signals, and USB signals to logic-level signals. It includes an internal 1.5kΩ USB pullup resistor and supports both full-speed (12Mbps) and low-speed (1.5Mbps) USB operation. The device features built-in ±15kV ESD protection circuitry for the USB I/O pins, D+ and D-. It operates with VL voltages as low as 1.65V, ensuring compatibility with low-voltage ASICs. The MAX3346E has a logic-selectable suspend mode that reduces current draw to less than 40µA. It also has an enumerate function that allows devices to logically disconnect while plugged in. The MAX3346E is fully compliant with USB specification 1.1 and supports full-speed and low-speed operation under USB specification 2.0. It is available in the miniature 4 x 4 chip-scale package (UCSP), as well as the small 14-pin TSSOP, and is rated for the -40°C to +85°C extended temperature range.