Intersil manuals, page 34
INTERSIL CA124/CA224/CA324/LM324/LM2902 handbook
CA124, CA224, CA324, LM324, LM2902 are four independent high-gain operational amplifiers suitable for commercial, industrial, and military applications. They can be powered by single or dual supplies, and have low power consumption and a wide input common-mode voltage range.
intersil CA158 CA158A CA258 CA358 CA358A CA2904 LM358 LM2904 Manual
CA158, CA158A, CA258, CA358, CA358A, CA2904, LM358, LM2904 are dual, 1MHz, operational amplifiers for commercial industrial, and military applications from the brand DINGHAO. They are designed specifically to operate from a single power supply over a wide range of voltages. They may also be operated from split power supplies.
intersil CA139 CA139A CA239 CA339 LM339 LM2901 LM3302 Manual
CA139, CA139A, CA239, CA339, LM339, LM2901, LM3302 Quad Voltage Comparators for Industrial, Commercial and Military Applications. The devices in this series consist of four independent single or dual supply voltage comparators on a single monolithic substrate. The common mode input voltage range includes ground even when operated from a single supply, and the low power supply current drain makes these comparators suitable for battery operation. These types were designed to directly interface with TTL and CMOS. Type CA139A, has a lower input offset voltage than the CA139. Some of the SOIC parts are available on tape and reel (see Ordering Information table). Replace the M suffix in the part number with M96 when ordering (e.g., CA0239M96).
intersil CA158 CA158A CA258 CA358 CA358A CA2904 LM358 LM2904 handbook
This document describes the features of CA158, CA158A, CA258, CA358, CA358A, and CA2904 types, which are dual channel, high gain, internally frequency compensated operational amplifiers. They can operate from a single power supply or split power supplies and are useful in interface circuits with digital systems, transducer amplifiers, and other conventional op amp circuits.
intersil ISL88031 Five voltage monitor Manual
The ISL88031 is a five-voltage monitor with industry-leading reset threshold accuracy and low power consumption. The device provides a variety of common features such as power-on reset, undervoltage supply monitoring, reset signaling and manual reset. The ISL88031 uses a small 8-pin MSOP package to monitor up to 5 different voltage levels, which can help reduce system costs, reduce board space requirements and improve system reliability.
intersil ISL88021 ISL88022 Five voltage monitor Manual
The ISL88021 and ISL88022 are customizable triple voltage-monitoring supervisors that assert a reset if any of the monitored voltages becomes non-compliant. They offer popular functions such as Power-On-Reset timing control with both RESET and RESET outputs, Supply Voltage Supervision, both under or overvoltage detection, and Manual Reset assertion. By offering these features in a small 8 Ld MSOP package, the ISL88021 and ISL88022 can lower system cost, reduce board space requirements and increase the reliability of systems.
intersil ISL6144 Five voltage monitor Manual
ISL6144 is a high voltage ORing MOSFET controller, it can be used to replace the power ORing diode in high current applications with a suitably sized N-Channel MOSFET to improve power distribution efficiency and availability
intersil HIP6602B Five voltage monitor Manual
The HIP6602B is a high frequency, two power channel MOSFET driver specifically designed to drive four power N-Channel MOSFETs in a synchronous rectified buck converter topology.
intersil HIP6601B HIP6603B HIP6604B Manual
The HIP6601B, HIP6603B and HIP6604B are high- frequency, dual MOSFET drivers specifically designed to drive two power N-Channel MOSFETs in a synchronous rectified buck converter topology.
intersil ISL6207 Manual
The ISL6207 is a high frequency, dual MOSFET driver, optimized to drive two N-Channel power MOSFETs in a synchronous-rectified buck converter topology in mobile computing applications.
intersil ISL6208 Manual
ISL6208 is a high-frequency, dual MOSFET driver optimized to drive two N-Channel power MOSFETs in a synchronous-rectified buck converter topology. It is especially suited for mobile computing applications that require high efficiency and excellent thermal performance. This driver, combined with an Intersil multiphase Buck PWM controller, forms a complete single-stage core-voltage regulator solution for advanced mobile microprocessors. The ISL6208 features 4A typical sinking current for the lower gate driver. This current is capable of holding the lower MOSFET gate off during the rising edge of the Phase node. This prevents shoot-through power loss caused by the high dv/dt of phase voltages. The operating voltage matches the 30V breakdown voltage of the MOSFETs commonly used in mobile computer power supplies. The ISL6208 also features a three-state PWM input that, working together with Intersil’s multiphase PWM controllers, will prevent negative voltage output during CPU shutdown. This feature eliminates a protective Schottky diode usually seen in a microprocessor power systems. MOSFET gates can be efficiently switched up to 2MHz using the ISL6208. Each driver is capable of driving a 3000pF load with propagation delays of 8ns and transition times under 10ns. Bootstrapping is implemented with an internal Schottky diode. This reduces system cost and complexity, while allowing the use of higher performance MOSFETs.
intersil ISL6208A Manual
intersil ISL6209 Manual
The ISL6209 is a high frequency, dual MOSFET driver, optimized to drive two N-Channel power MOSFETs in a synchronous-rectified buck converter topology in mobile computing applications. This driver, combined with an Intersil Multi-Phase Buck PWM controller, such as ISL6216, ISL6244, and ISL6247, forms a complete single-stage core-voltage regulator solution for advanced mobile microprocessors. The ISL6209 features 4A typical sink current for the lower gate driver. The 4A typical sink current is capable of holding the lower MOSFET gate during the PHASE node rising edge to prevent the shoot-through power loss caused by the high dv/dt of the PHASE node. The operation voltage matches the 30V breakdown voltage of the MOSFETs commonly used in mobile computer power supplies. The ISL6209 also features a three-state PWM input that, working together with most of Intersil multiphase PWM controllers, will prevent a negative transient on the output voltage when the output is being shut down. This feature eliminates the Schottky diode, that is usually seen in a microprocessor power system for protecting the microprocessor, from reversed-output-voltage damage. The ISL6209 has the capacity to efficiently switch power MOSFETs at frequencies up to 2MHz. Each driver is capable of driving a 3000pF load with a 8ns propagation delay and less than a 10ns transition time. This product implements bootstrapping on the upper gate.
intersil ISL6210 Manual
The ISL6210 is a dual-power synchronous rectified MOSFET driver from Intersil. It is optimized to drive two independent power channels in a synchronous-rectified buck converter topology. The ISL6210 together with an Intersil ISL62xx multiphase PWM controller forms a complete single-stage core-voltage regulator solution with high efficiency performance at high switching frequency for advanced microprocessors. The IC is biased by a single low voltage supply (5V), minimizing driver switching losses in high MOSFET gate capacitance and high switching frequency applications. Each driver is capable of driving a 3nF load with less than 10ns rise/fall time. Bootstrapping of the upper gate driver is implemented via an internal low forward drop diode, reducing implementation cost, complexity, and allowing the use of higher performance, cost effective N-Channel MOSFETs. Adaptive shoot-through protection is integrated to prevent both MOSFETs from conducting simultaneously. The ISL6210 features 4A typical sink current for the lower gate driver, enhancing the lower MOSFET gate hold-down capability during PHASE node rising edge, preventing power loss caused by the self turn-on of the lower MOSFET due to the high dV/dt of the switching node. The ISL6210 also features an input that recognizes a high- impedance state, working together with Intersil multiphase PWM controllers to prevent negative transients on the controlled output voltage when operation.
intersil ISL6594A ISL6594B Manual
ISL6594A and ISL6594B are high frequency MOSFET drivers specifically designed to drive upper and lower power N-Channel MOSFETs in a synchronous rectified buck converter topology.