Intersil manuals, page 33
INTERSIL ISL54000 ISL54001 ISL54002 Manual
The Intersil ISL54000, ISL54001, ISL54002 are integrated audio power amplifier systems that combine stereo BTL 8Ω amplifiers in a single package
INTERSIL - ISL8104 handbook
ISL8104 8V to 14V, Single-Phase Synchronous Buck Pulse-Width Modulation (PWM) Controller With Integrated Gate Drivers
INTERSIL - EL5166 EL5167handbook
The EL5166 and EL5167 amplifiers are 1.4GHz current feedback amplifiers with enable function, suitable for high-speed video, monitor, RF, and IF frequency designs. They have a high bandwidth of 1.4GHz, a supply current of just 8.5mA, and can operate from a single supply voltage of 5V to 12V.
INTERSIL ISL59446 handbook
The ISL59446 is a 500MHz bandwidth four-way quarter gain multiplexing amplifier from Intersil. It has a high gain, high speed and excellent bandwidth, and is suitable for video switching.
INTERSIL EL8108 Manual
EL8108 is a video distribution amplifier from Intersil with high driving capability and low quiescent current.
intersil EL7156 Manual(1)
The EL7156 is a high performance pin driver with three-state is suited to many ATE and level-shifting applications.
INTERSIL HA4314B Manual
The HA4314B is a very wide bandwidth 4x1 crosspoint switch ideal for professional video switching, HDTV, computer monitor routing, and other high performance applications. The circuit features very low power dissipation (105mW Enabled, 4mW Disabled), excellent differential gain and phase, and very high off isolation. When disabled, the output is switched to a high impedance state, making the HA4314B ideal for routing matrix equipment. The HA4314B requires no external current source, and features fast switching and symmetric slew rates. For a 4x1 crosspoint with Tally outputs (channel indicators) or with synchronous control signals, please refer to the HA4404B and HA4344B data sheets, respectively. For audio channels requiring larger signal swings, please refer to the CD22M3494 (16x8) data sheet.
INTERSIL ISL1539 Manual
The ISL1539 is a dual channel differential VDSL2 line driver used for high performance long reach and high-speed applications. The driver has been optimized for flat gain response, reduced harmonic distortion, and noise to improve the overall signal to noise ratio in the system. The drivers achieve a total harmonic distortion (THD) measurement of typically -60dB MTPR @ 1.1MHz, while consuming typically 10mA per DSL channel of total supply current. The device operates on ±5V to ±15V supplies and retains its bandwidth and linearity over the complete supply range. It is supplied in a small footprint (4mmx5mm) 24 Ld QFN package and is specified for operation over the full -40°C to +85°C temperature range.
intersil PROFET BTS 432 F2 handbook
This document describes the features and characteristics of the PROFET BTS 432 F2 smart highside power switch produced by Infineon Technologies AG, including load dump and reverse battery protection, negative voltage clamp at the output, short-circuit protection, current limitation, thermal shutdown, diagnostic feedback, open load detection in ON-state, CMOS compatible input, electrostatic discharge (ESD) protection, loss of ground and loss of Vbb protection, overvoltage protection, and undervoltage and overvoltage shutdown with auto-restart and hysteresis. The product is a microcontroller compatible power switch with diagnostic feedback for 12V and 24V DC grounded loads, most suitable for inductive loads, and can replace electromechanical relays and discrete circuits.
intersil PROFET BTS 432 F2 datasheet
This document describes the features and characteristics of Infineon Technologies AG's PROFET® BTS 432 F2 smart highside power switch, including load dump and reverse battery protection, negative voltage clamp at output, short-circuit protection, current limitation, thermal shutdown, diagnostic feedback, open load detection, CMOS compatible input, electrostatic discharge protection, loss of ground protection, overvoltage protection, undervoltage and overvoltage shutdown.
intersil PROFET BTS 432 E2 Smart Highside Power Switch datasheet
This is a high-end smart power switch with load dump and reverse battery protection, negative voltage clamp at output, short-circuit protection, current limitation, thermal shutdown, diagnostic feedback, open load detection, CMOS compatible input, electrostatic discharge (ESD) protection, ground loss and Vbb loss protection, overvoltage protection and other functions. It is suitable for 12V and 24V DC grounded loads of µC compatible power switch, and can replace electromechanical relays and discrete circuits.
intersil SPP 30N03 handbook
intersil SPP24N60C3 handbook
SPP24N60C3 is a high voltage power transistor, its features are new revolutionary high voltage technology, worldwide best RDS(on) in TO220, ultra low gate charge, periodic avalanche rated, extreme dv/dt rated, ultra low effective capacitances and improved transconductance.
intersil SPP24N60C3 datasheet
This datasheet provides information about SPP24N60C3, including maximum voltage, current and power consumption.
intersil ISL6562 Microprocessor CORE Voltage Regulator Two-Phase Buck PWM Controller Manual
ISL6562 is a two-phase buck PWM controller for microprocessor CORE voltage regulation. This device together with companion gate drivers, HIP6601A, HIP6602A, HIP6603A or HIP6604 and MOSFETs provides a precision voltage regulation system for advanced microprocessors to satisfy the ever increasing current demands of modern microprocessors.