Texas Instruments Manuals

The DAC7632 is a 16-bit dual channel voltage output DAC from TI, it supports single or dual supply, the operating temperature range is -40°C to +85°C, it has low power, high accuracy, low noise, and is suitable for industrial process control, data acquisition systems, closed-loop servo control and other applications.

The ADS1110 is a precision, continuously self-calibrating Analog-to-Digital (A/D) converter with differential inputs and up to 16 bits of resolution in a small SOT23-6 package. Its features include: onboard 2.048V reference, onboard PGA, onboard oscillator, 16-bit no missing codes, continuous self-calibration, single-cycle conversion, programmable data rate, I2C interface, power supply ranging from 2.7V to 5.5V, low current consumption, etc. It is suitable for applications such as portable instrumentation, industrial process control, smart transmitters, consumer goods, factory automation, temperature measurement, etc.

The TAS5713 is a 25-W, efficient, digital-audio power amplifier for driving stereo bridge-tied speakers. It features EQ and DRC, supports BTL configuration, eliminates the need for heatsinks, and supports a sample rate range of 8kHz to 48kHz.

LM124, LM124A, LM224, LM224A LM324, LM324A, LM324Y, LM2902, LM2902Q are a series of four operational amplifiers produced by TI. They have wide range supply voltages (single supply voltage 3V to 30V, dual supply voltage 3V to 26V), low supply current consumption (independent of supply voltage), common mode input voltage range includes ground (reliable detection of ground nearby voltages), low input bias and offset parameters (input offset voltage 3mV typical, A version 2mV typical; input offset current 2nA typical; input bias current 20nA typical, A version 15nA typical) and equal to maximum rated supply voltage differential input voltage range (32V, LM2902 and LM2902Q is 26V).

PCI7410 SLLA247 is TI's PC Card, UltraMedia™ and Integrated 1394a-2000 OHCI Two-Port PHY/Link-Layer Controller that is fully interoperable with FireWire™ and i.LINK™ implementations of IEEE Std 1394 and supports IEEE Std 1394a-2000 connection, short reset, multispeed concatenation, arbitration acceleration, fly-by concatenation and port disable/suspend/resume

This manual provides design information for the SCPS172 Connectivity Solutions.

This is a triple-cable transceiver/arbiter that fully supports the provisions of IEEE 1394-1995 standard for high performance serial bus

This data sheet provides details of the SPRS079E including its features, technical specifications and application instructions.

This document describes the S100B port failed connection issue of TSB41BA3/A and provides some workarounds

无

Texas Instruments and its subsidiaries reserve the right to make changes to their products or to discontinue any product or service without notice. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability.

CY74FCT163374 and CY74FCT163H374 are 16-bit registers designed for use as buffered registers in high-speed, low power bus applications. They can be used as two independent 8-bit registers or as a single 16-bit register by connecting the output enable (OE) and clock (CLK) inputs. The outputs are 24-mA balanced output drivers with current limiting resistors to reduce the need for external terminating resistors, and provide for minimal undershoot and reduced ground bounce.

The 78SR100 is a series of wide input voltage, 3-terminal Integrated Switching Regulators (ISRs). These ISRs have a maximum output current of 1.5A and an output voltage that is laser trimmed to a variety of industry standard voltages. These 78 series regulators have excellent line and load regulation with internal short-circuit and over-temperature protection, are very flexible, and may be used in a wide variety of applications.

This document describes the features and characteristics of TIBPAL20 series high-performance IMPACT-X PAL circuits, including high-performance operation, preload capability, power-up clear function, package options, and security fuse.

The DRV593 and DRV594 are high-efficiency, high-current power amplifiers ideal for driving a wide variety of thermoelectric cooler elements in systems powered from 2.8 V to 5.5 V. The operation of the device requires only one inductor and capacitor for the output filter, saving significant printed-circuit board area. Pulse-width modulation (PWM) operation and low output stage on-resistance significantly decrease power dissipation in the amplifier. The DRV593 and DRV594 are internally protected against thermal and current overloads. Logic-level fault indicators signal when the junction temperature has reached approximately 115°C to allow for system-level shutdown before the amplifier’s internal thermal shutdown circuitry activates. The fault indicators also signal when an overcurrent event has occurred. If the overcurrent circuitry is tripped, the device will perform a system-level shutdown.