ANALOG Manuals

The ADL5902 Rev. A is a high performance power detector that provides DC output for power amplifier linearization/control loops, transmitter power control, transmitter signal strength indication (TSSI) and RF instrumentation.

The ADL5504 is a TruPwr detector with a frequency range of 450 MHz to 6000 MHz. It features true RMS response, excellent temperature stability, and can be used for power measurement of W-CDMA, CDMA2000, QPSK-/QAM-based OFDM, and other applications.

The AD8363 is a single-ended input rms-to-dc converter with an input dynamic range of greater than 50 dB from 50 Hz to 6 GHz. It features no balun or external input tuning requirements and provides waveform and modulation independent RF power detection.

The document describes the features and characteristics of the ADL5502 Crest Factor Detector. This detector has a true rms response and envelope peak hold output, excellent temperature stability, and can operate in the frequency range of 450 MHz to 6000 MHz. It is suitable for power and envelope measurement of complex modulation waveforms such as W-CDMA, CDMA2000, and QPSK-/QAM-based OFDM.

The ADL5501 is a mean-responding TruPwr™ power detector for use in high frequency receiver and transmitter signal chains from 50 MHz to 6 GHz. It is easy to apply, requiring only a single supply between 2.7 V and 5.5 V and a 50 Ω input impedance.

The ADL5500 is a mean-responding power detector for use in high frequency receiver and transmitter signal chains from 100 MHz to 6 GHz. It is easy to apply, requiring only a single external capacitor and a low input impedance voltage reference. It features ±0.1 dB temperature stability and up to 30 dB input dynamic range, making it suitable for a variety of applications.

The AD8362 is a true rms-responding power detector that has a 65 dB measurement dynamic range and can accurately convert rms to dc from 50 Hz to 3.8 GHz. The AD8362 operates from 4.5 V to 5.5 V at 24 mA and has a standby power of 1.3 mW.

AD8361 is a mean-responding power detector for use in high frequency receiver and transmitter signal chains, up to 2.5 GHz. It features calibrated rms response, excellent temperature stability, and a wide input range.

The ADG467 is an octal channel protector that protects sensitive components from voltage transience in the signal path. It features fault and overvoltage protection, low on resistance, low power dissipation, and latch-up proof construction.

ADG465 is a single channel protector in an SOT-23 package, that can protect sensitive components from voltage transients

The AD1580 is a low-cost, 2-terminal (shunt), precision band gap reference. It provides an accurate 1.225 V output for input currents between 50 μA and 10 mA.

The AD800 and AD802 employ a second order phase-locked loop architecture to perform clock recovery and data retiming on Non-Return to Zero, NRZ, data. This architecture is capable of supporting data rates between 20 Mbps and 160 Mbps. The products described here have been defined to work with standard telecommunications bit rates. 45 Mbps DS-3 and 52 Mbps STS-1 are supported by the AD800-45 and AD800-52 respectively. 155 Mbps STS-3 or STM-1 are supported by the AD802-155. Unlike other PLL-based clock recovery circuits, these devices do not require a preamble or an external VCXO to lock onto input data. The circuit acquires frequency and phase lock using two control loops.

The AD807 is a fiber optic receiver with a quantizer and clock recovery and data retiming. It meets CCITT G.958 requirements and Bellcore TR-NWT-000253 requirements. It accepts NRZ data, no preamble required, and has a 2.0 degrees RMS output jitter. It uses phase-locked loop type clock recovery, no crystal required. Its quantizer sensitivity is 2 mV, level detect range is 2.0 mV to 30 mV, single supply operation is +5 V or -5.2 V, low power is 170 mW, 10 KH ECL/PECL compatible output, 16-lead narrow 150 mil SOIC package.

The AD808 is a fiber optic receiver with quantizer and clock recovery and data retiming. The product meets the CCITT G.958 standard and the Bellcore TR-NWT-000253 standard, supports 622 Mbps clock recovery and data retiming, accepts NRZ data, does not require a preamble code, and uses a phase-locked loop clock recovery, without a crystal.

The ADN2804 provides the receiver functions of quantization, signal level detect, clock and data recovery, and data retiming for 622 Mbps Ethernet, BPON ONT, SONET OC-12 WDM transponders, Regenerators/repeaters, Test equipment, Broadband cross-connects and routers.