Industrial

The AD7674 is a 18-bit, 2.5 LSB INL, 800 kSPS SAR ADC with 18-bit resolution, no missing codes, no pipeline delay (SAR architecture) and 5 V input range.

AD9865 is a low-cost 3.3 V CMOS MxFETM for broadband modems. It features a 10-bit D/A converter, 2×/4× interpolation filter, 200 MSPS DAC update rate, integrated 23 dBm line driver with 19.5 dB gain control, 10-bit, 80 MSPS A/D converter, -12 dB to +48 dB low noise RxPGA(<3.0 nV/rtHz), third order programmable low-pass filter, flexible digital data path interface, half- and full-duplex operation, backward-compatible with AD9975 and AD9875, various power-down/reduction modes, internal clock multiplier (PLL), 2 auxiliary programmable clock outputs, available in 64-lead chip scale package or bare die.

The BYD31 series is a fast soft-recovery controlled avalanche rectifier, featuring glass passivation, high maximum operating temperature, low leakage current, excellent stability, and guaranteed avalanche energy absorption capability.

The AD9863 Rev. A is a mixed-signal front-end (MxFE™) baseband transceiver from Analog Devices that is suitable for broadband applications. The AD9863 Rev. A has dual 12-bit, 50 MSPS analog-to-digital converters and dual 12-bit, 200 MSPS digital-to-analog converters, and supports internal or external references. The AD9863 Rev. A also supports various interleaved or noninterleaved data transfer modes, and can operate in half-duplex mode or full-duplex mode. The AD9863 Rev. A uses a 24-pin flexible I/O data interface, and supports programming through registers or through mode pins. The AD9863 Rev. A also has independent Rx and Tx power-down control pins, and a 64-lead LFCSP package (9 mm × 9 mm).

This document describes a 16-bit 100 kSPS PulSAR® unipolar ADC with a 2.5V internal reference. It features a throughput of 100 kSPS, INL of ±2.5 LSB max, and a resolution of 16 bits. The ADC has both AC and DC specifications, no pipeline delay, and a parallel and serial 5V/3V interface. It is suitable for applications such as data acquisition, medical instruments, and digital signal processing.

The AD7652 is a 16-bit, 500 kSPS unipolar ADC with features including high throughput, 0-2.5V analog input voltage range, no pipeline delay, parallel and serial interfaces, etc.

AD7651 is a 16-bit, 100kSPS, single-channel, serial/parallel interface, low power SAR ADC that supports SPI, QSPI, MICROWIRE, DSP, etc.

The AD7457 is a low power pseudodifferential 12-bit ADC with an 8-lead SOT-23 package. It operates in a voltage range of 2.7V to 5.25V and features low power consumption, wide input bandwidth, flexible power/serial clock speed management, etc. The ADC is suitable for applications such as transducer interface, battery-powered systems, data acquisition systems, and portable instrumentation.

The AD74531 is a 12-bit, high speed, low power, successive approximation (SAR) analog-to-digital converter that features a pseudo differential analog input. This part operates from a single 2.7 V to 5.25 V power supply.

The BUF420A is a STMicroelectronics High Voltage Fast-Switching NPN Power Transistor. It features high voltage capacity, very high switching speed, minimum lot-to-lot spread for reliable operation and low base-drive requirements. The BUF series is designed for use in high-frequency power supplies and motor control applications.

PROFET® BTS 432 E2 is a high side power switch with negative voltage clamp, short circuit protection, current limitation, thermal shutdown, diagnostic feedback, open load detection, CMOS compatible input, electrostatic discharge protection, loss of ground and loss of Vbb protection. It is suitable for all types of resistive, inductive and capacitive loads with 12 V and 24 V DC ground.

BTA/BTB16 and T16 series SNUBBERLESS™, LOGIC LEVEL & STANDARD 16A TRIACS are suitable for general purpose AC switching, and can be used as ON/OFF function in applications such as static relays, heating regulation, induction motor starting circuits, or for phase control operation in light dimmers, motor speed controllers, .

This document introduces the product characteristics of Philips Semiconductors BT137B series triacs, including rated voltage, rated current, working temperature and other parameters.

R0201-BS62LV2008 Revision 1.1 Jan. 2004 1 A17 is a very low power/voltage CMOS SRAM with a capacity of 256K x 8 bits. The features of this product include an operating voltage range of 4.5V to 5.5V, very low power consumption, and high-speed access time. It also has features such as automatic power down, three-state outputs, and TTL compatibility.