Industrial

This datasheet provides detailed information about Motorola TMOS DUAL TMOS MOSFET products, including brand, model, product features, etc.

MMBTH10LT1 is a NPN silicon small signal transistor produced by Motorola company, its maximum collector-emitter voltage is 25Vdc, maximum collector-base voltage is 30Vdc, maximum emitter-base voltage is 3.0Vdc.

HYB3164805BJ/BT(L)-40/-50/-60 8M x 8-Bit Dynamic RAM (4k & 8k Refresh, EDO-version) is a 64 MBit dynamic RAM organized 8 388 608 by 8 bits. The chip supports EDO mode and operates in the temperature range of 0 to 70 °C. It has a single + 3.3 V (± 0.3V) power supply and low power dissipation.

This datasheet lists the features of DL5221 THRU DL5281 500 mW Zener Diode 2.4 to 200 Volts, including operating temperature range, maximum power dissipation, capacitance, package size, etc.

MM1108 is a no-adjustment sync separator IC designed for use in VCR, TV and other video equipment. Main features include: low current consumption (4.4mA), open collector output, built-in 3V regulator, built-in vertical sync separation capacitor, supports both PAL and NTSC formats, sync separation level can be adjusted with external resistors.

This document describes the features of TMC 93LC46/56/57/66/86 series Microwire serial EEPROM products, including high-speed operation, low power consumption, selectable x8 or x16 memory organization, self-timed write cycle, hardware and software write protection, power-up inadvertent write protection, 1,000,000 program/erase cycles, and 100-year data retention.

The TMC2242A/B are fixed-coefficient linear-phase half-band (low-pass) digital filters. They can be used to halve or double the sampling rate of a digital signal. When used as a decimating post-filter with a double-speed oversampling A/D converter, they greatly reduce the cost and complexity of anti-aliasing filters required ahead of the A/D converter. When used as an interpolating pre-filter with a double-speed oversampling D/A converter, the TM2242A/B can provide very low passband ripple and up to 59.4 dB of stopband rejection.

11DQ03L is a Schottky diode produced by Texas Instruments. It features a small size, low voltage drop, low power loss, high efficiency and high surge capability.

The TLV278x series is a single supply operational amplifiers from TI, with a supply voltage range of 1.8V to 3.6V, Rail-to-Rail input and output capability, bandwidth of 8MHz, high slew rate of 4.8V/µs, input noise voltage of 9nV/√Hz at 10kHz, rated temperature range of 0°C to 70°C(commercial grade), -40°C to 125°C(industrial grade), package form of PDIP, SOIC, and the newer SOT-23(single), MSOP(dual), and TSSOP(quad).

The AD603 is a low noise, voltage-controlled amplifier for use in RF and IF AGC systems. It provides accurate, pin selectable gains of -11 dB to +31 dB with a bandwidth of 90 MHz or 9 dB to 51 dB with a bandwidth of 9 MHz. Any intermediate gain range may be arranged using one external resistor. The input referred noise spectral density is only 1.3 nV/√Hz and the output referred power spectral density is -126 dBm/Hz. The device has good linearity, with a maximum gain error of ±0.5 dB and a dynamic range of 60 dB.

AD603 is a low noise, voltage-controlled amplifier from ADI that provides accurate, pin selectable gains of -11 dB to +31 dB with a bandwidth of 90 MHz or +9 dB to +51 dB with a bandwidth of 9 MHz. Any intermediate gain range may be arranged using one external resistor. The input referred noise spectral density is only 1.3 nV/√Hz and power consumption is 125 mW at the recommended ±5 V supplies.

The ML4825 is a high frequency PWM controller optimized for use in switch mode power supply designs running at frequencies to 1MHz.

Motorola Thyristor Device Data is a datasheet introducing Motorola thyristor devices. The device is designed for direct interface with the AC power line. Upon reaching the breakover voltage in each direction, the device switches from a blocking state to a low voltage on-state. Conduction will continue like an SCR until the main terminal current drops below the holding current. The plastic axial lead package provides high pulse current capability at low cost. Glass passivation ensures reliable operation. Applications include: High Pressure Sodium Vapor Lighting, Strobes and Flashers, Ignitors, High Voltage Regulators, Pulse Generators.

The AD600/AD602 are dual channel, low noise, wideband variable gain amplifiers optimized for use in ultrasound imaging systems but are applicable to any application requiring precise gain, low noise and high bandwidth.