Industrial

ADSP-2186L is a DSP microcomputer with 25ns instruction cycle time, 40 MIPS sustained performance, single-cycle instruction execution, single-cycle context switching, 3-bus architecture, low CMOS standby power dissipation with 400 cycle recovery from power-down condition, low power dissipation in idle mode.

The MIC2025 and MIC2075 are high-side MOSFET switches optimized for general-purpose power distribution requiring circuit protection. The MIC2025/75 are internally current limited and have thermal shutdown that protects the device and load. The MIC2075 offers “smart” thermal shutdown that reduces current consumption in fault modes. When a thermal shutdown fault occurs, the output is latched off until the faulty load is removed. Removing the load or toggling the enable input will reset the device output. Both devices employ soft-start circuitry that minimizes inrush current in applications where highly capacitive loads are employed. A fault status output flag is provided that is asserted during overcurrent and thermal shutdown conditions. The MIC2025/75 is available in the MM8™ 8-lead MSOP and 8-lead SOP.

The MedSystem III® Multi-Channel Infusion Pump is a multi-channel infusion pump with advanced dose rate calculation. It features a compact size, three independent fluid delivery systems, accurate delivery of various fluids, and accommodates different container types.

VisualDSP++ 4.0 Getting Started Guide introduces the features of VisualDSP++ 4.0 and provides detailed instructions for use.

W4.0 C/C++ Compiler and Library Manual for TigerSHARC Processors is the reference manual for TigerSHARC processors, introduces the use of the compiler and the use of library functions.

ADSP-BF561 EZ-KIT Lite® Evaluation System Manual, Describes the features and characteristics of the ADSP-BF561 EZ-KIT Lite® Evaluation System

This manual introduces the features and use of the ADSP-BF548 EZ-KIT Lite evaluation system.

This document provides the installation procedure for EZ-KIT Lite, including the installation of VisualDSP++ software and hardware, as well as the registration and limited warranty of EZ-KIT Lite.

This document introduces the characteristics and features of Micrel MIC184 Local/Remote Thermal Supervisor, including measuring local and remote temperatures, compatibility with LM75, 9-bit sigma-delta ADC, 2-wire I2C/SMBus compatible interface, programmable temperature settings, etc.

Micrel MIC2003/2013 are high-side current limiting devices, designed for power distribution applications in PCs, PDAs, printers and peripheral devices.

The MIC1832 is a multifunction circuit which monitors microprocessor activity, external reset and power supplies in microprocessor based systems. The circuit functions include a watchdog timer, power supply monitor, microprocessor reset, and manual pushbutton reset input. The power supply line is monitored with a comparator and an internal voltage reference. RST is forced low when an out-of-tolerance condition exists and remains asserted for at least 250ms after VCC rises above the threshold voltage (2.55V or 2.88V). The RST pin will remain logic low with VCC as low as 1.4V. The Watchdog input (ST) monitors µP activity and will assert RST if no µP activity has occurred within the watchdog timeout period. The watchdog timeout period is selectable with a nominal periods of 150, 600, or 1200 milliseconds.

The MIC1815 is a Microprocessor Reset Circuit from Micrel, it monitors the power supply in microprocessor based systems and generates a reset signal when the supply voltage drops below a pre-determined reset threshold voltage. There are a number of different reset threshold voltages available to accommodate 10% or 20% drop in 3.3V powered systems. The MIC1815 has a low-level RESET output. The reset output is guaranteed to remain asserted for a minimum of 100ms after VCC has risen above the designated reset threshold level. The MIC1815 is available in a 3-lead SOT-23 package.

This manual describes the use of the VisualDSP++ 4.5 Loader and Utilities.