Industrial

The L9374 is a four channel low side driver with integrated recirculation diodes. It features a programmable channel timer, clock monitor, detailed load diagnosis, etc.

The L9390 is a twelve output low side valve driver designed for use in an ABS/ESP vehicle system. All outputs are PWM configurable, while six out of twelve are current regulated. Each of the twelve outputs is open drain configured and has a built-in 35V clamp. Eight of the twelve have integrated active freewheeling diodes for active rectification of the PWM controlled load. In order to minimize electromagnetic emissions during load actuation, the possibility to control output slopes is provided. Two separate communication interfaces support SPI communication for configuration and diagnostics.

VL5510 is a high dynamic range CMOS sensor from STMicroelectronics. The sensor has a resolution of 1024 x 512 monochrome and 5.6µm x 5.6µm high dynamic pixels. It supports parallel video data output interface, high-speed serial link interface, I2C control interface, SPI slave control interface, UART control interface, SPI master interface.

This document describes the features of the STA260 Sirius SDARS channel, service, and source decoder from STMicroelectronics. It includes 2 satellite and 1 terrestrial signal demodulators and decoders, an advanced DSP processor to implement PAC audio decoder, and other specifications.

SPC563Mxx is a 32-bit Power Architecture® based MCU from ST, mainly used for automotive powertrain applications.

This document describes the features and characteristics of the SPC560P50L3, SPC560P50L5, SPC560P44L3, and SPC560P44L5, which are 32-bit Power Architecture™ based MCU products. It includes a single-issue, 32-bit CPU core complex, variable length encoding (VLE), on-chip flash memory with ECC, on-chip RAM with ECC, fail-safe protection, Nexus L2+ interface, interrupt controller, general purpose I/O, timers, and communication interfaces.

This document describes the STA1052 DSP/MCU system from STMicroelectronics, which is designed for CD-DA, CD-CA, and CD-ROM players. It features CD-R and CD-RW playback, audio decoding (MP3, WMA, AAC), CLV (1x, 2x, 4x) and CAV mode (6x), and more.

32-bit MCU family built on the Power Architecture for automotive body electronics applications

The document introduces the features and characteristics of the L9352B four-channel valve driver product, including four low-voltage output drivers, short circuit protection, selective overtemperature shutdown, open load and overload current detection, ground and power supply loss detection, external clock control, recirculation path control, regulator drift detection, regulator error control, electrostatic discharge (ESD) protection, etc.

The TDA7801 is a new BCD technology quad bridge amplifier for car audio applications. Thanks to the BCD6 technology it is possible to integrate a high performance D/A converter together with powerful MOSFET outputs. The possibility of having the D/A conversion on board allows the performance to reach an outstanding 115 dB S/N ratio with more than 105 dB of dynamic range.

The L99H01 is a DC-motor driver for automotive applications from STMicroelectronics with a maximum operating voltage of 28V, support for 100% duty cycle, reverse battery protection, PWM operation, and an SPI interface and a freely configurable current sense amplifier.

The SPC56EL60L3 SPC56EL60L5 is a high-performance 32-bit Power Architecture® microcontroller from STMicroelectronics for automotive SIL3/ASILD chassis and safety applications.

The L99PM62XP is a power management system IC providing electronic control units with enhanced system power supply functionality including various standby modes as well as LIN and HS CAN physical communication layers. It contains two low drop voltage regulators, one for microcontroller supply and one for peripheral supply. Both regulators have ultra low quiescent current, which can significantly reduce system power consumption in standby modes.

L99PM60J is ST's low voltage power management system IC. It contains a low voltage 5V regulator, 2 high side drivers, a LIN 2.1 transceiver and a standard serial peripheral interface (SPI).