MOTOROLA Manuals

This file is a conformity declaration for the PC850 product. It states that the product meets the requirements of the European Union's Radio and Telecommunications Terminal Equipment Directive (1999/5/EC).

This document is a Declaration of Conformity regarding R&TTE (Radio & Telecommunications Terminal Equipment Directive). The certifying organization is Motorola, Inc. The declared product is a Bluetooth power class 2 wireless terminal with the model names HF800, HF820, HF820CE. The product(s) listed above conform with the essential requirements of European Union Directive 1999/5/EC.

This document is the declaration of conformity for Motorola S305 Bluetooth headset in Europe

This document is a declaration of conformity for the H520, H525 Bluetooth headsets, which meet all the essential requirements of the European Union Directive 1999/5/EC.

This document is a CE certificate, which proves that Motorola H790 wireless Bluetooth headset complies with the basic requirements of European Union R&TTE directive.

This document is a declaration of conformity, published by Motorola Inc., to prove that its Bluetooth headset H17 meets all the essential requirements of the European Union 1999/5/EC Directive.

P6SMB160 is a type of P6SMB series and a MOSFET device launched by ON Semiconductor.

500 milliwatt glass sealed zener diodes

This document describes the features and characteristics of the Motorola M68HC12 microcontroller MC68HC912D60/D.

This document introduces the MPX2010/MPXV2010G series silicon piezoresistive pressure sensors, which provide a very accurate and linear voltage output that is directly proportional to the applied pressure. These sensors house a single monolithic silicon die with the strain gauge and thin-film resistor network integrated on each chip. The sensor is laser trimmed for precise span, offset calibration and temperature compensation.

This data sheet provides information on the B130 Schottky diode. It has a low forward voltage drop, a small package, and good stability and high temperature resistance.

The MC10SX1126 is an integrated limiting amplifier for high frequency fiber optic applications. The device interfaces directly to the trans-impedance amplifier of a typical optical to electrical conversion portion of a fiber optic link. With data rate capabilities in the 1.25Gb/s range, the high gain limiting amplification of the SX1126 is ideal for high speed fiber optic applications like SONET/SDM, ATM, FDDI, Fibre Channel or Serial Hippi. The device is functionally and pin compatible to the Signetics SA5225 with a significantly higher bandwidth. The CAZP and CAZN inputs to the limiting amplifier provide an auto-zero function to effectively cancel any input offset voltage present in the amplifier. The SX1126 incorporates a programmable level detect function to identify when the input signal has been lost. This information can be fed back to the Disable input of the device to maintain stability under loss of signal conditions. Using the Vset pin the sensitivity of the level detect can be adjusted. The CLD input is used to filter the level detect input so that random noise spikes are filtered out. The MC10SX1126 is compatible with MECL10H logic levels.

The MCM67M518 is a synchronous static random access memory designed to provide a burstable, high-performance, secondary cache for the MC68040 and PowerPC microprocessors. It is fabricated using Motorola's high-performance silicon-gate BiCMOS technology and integrates input registers, a 2-bit counter, high-speed SRAM, and high drive capability outputs onto a single monolithic circuit. The synchronous design allows precise cycle control with the use of an external clock. Bursts can be initiated with either transfer start processor or transfer start cache controller input pins. Write cycles are internally self-timed and initiated by the rising edge of the clock input.

The MPX5100/MPXV5100 series piezoresistive transducer is a state-of-the-art monolithic silicon pressure sensor designed for a wide range of applications, particularly those employing a microcontroller or microprocessor with A/D inputs. This sensor combines advanced micromachining techniques, thin-film metallization, and bipolar processing to provide an accurate, high level analog output signal that is proportional to the applied pressure.