Tyco manuals, page 2
TYCO EP/VP SERIES DATA SHEET
The product is a power line filter that is used to suppress switching power supply noise. It meets the requirements of CISPR in Europe and FCC specifications in the USA. It has high insertion loss and low leakage current.
TYCO B SERIES DATA SHEET
The product is CORCOM B series RFI power line filters, which are suitable for high impedance loads, low cost, small size and high efficiency RFI control of line-to-ground noise.
TYCO H SERIES DATA SHEET
The H series filters were developed specifically for health care applications. These products are suitable for uses in both patient care equipment and non-patient care equipment. Their extremely low leakage current allows compliance with UL2601 and CSA 22.2 health care specifications.
TYCO EMC SERIES Datasheet
The EMC series of RFI filters has been developed to reduce conducted noise to acceptable limits for equipment that must comply with the requirements of CISPR in Europe and the FCC specifications in the USA. The EMC series is the most compact dual stage filter available from Tyco Electronics. This cost effective design has a maximum current rating of 30 amps; higher than any similar catalog product. The EMC series was designed to address the need for more differential mode attenuation in the lower frequency range while still maintaining high common mode performance. This type of performance is typically needed for motor drives and switch mode power supplies with increased operating frequencies. The EMC series is ideal for applications that require a high level of performance in a compact, cost effective package.
TYCO K SERIES Datasheet(1)(1)
The K series RFI power line filters are general purpose common-mode and differential-mode filters. They are effective in the control of line-to-line as well as line-to- ground RFI interference. The K series RFI filters are particularly suited in applications where pulsed, continuous and/or intermittent RFI interference is present. The EK models meet the very low leakage current requirements of VDE portable equipment, and (120 Volt) UL544 non-patient medical equipment.
TYCO K SERIES Datasheet(1)
The K series RFI power line filters are general purpose common-mode and differential-mode filters. They are effective in the control of line-to-line as well as line-to- ground RFI interference. The K series RFI filters are particularly suited in applications where pulsed, continuous and/or intermittent RFI interference is present. The EK models meet the very low leakage current requirements of VDE portable equipment, and (120 Volt) UL544 non-patient medical equipment.
TYCO R SERIES Datasheet
This dual T section RFI power line filter provides premium performance at moderate cost. They are well suited for low impedance loads where noisy RFI environments are present. They control pulsed, continuous and/or intermittent interference, providing protection to your equipment from power line noise in addition to protecting the line from equipment noise. The R series dual T type provides low leakage current without deterioration of insertion loss characteristics and at a competitive cost. The ER models meet the low leakage current requirements of VDE portable equipment, and (120 Volt) UL2601 non-patient medical equipment.
TYCO Q SERIES Datasheet
This product guide introduces the CORCOM series highest performance RFI filters, which are specifically designed for switching power supplies and are intended to provide all the power line filtering needed to control conducted emissions all the way down to 10kHz.
TYCO T SERIES Datasheet
The T series RFI filters provide superior common-mode and premium differential-mode attenuation, exceeded only by that of Q series filters. This remarkable performance is available for current ratings up to 20 amps in package sizes smaller than comparable EP series filters. These filters are a size and cost-effective choice for very noisy equipment that must meet the emission limits of FCC Parts 15 and 18 or EN55022, A-level. In some cases, these filters can even bring equipment into compliance with EN55022, B-level. This performance is accomplished with circuits that still meet the very low leakage current requirements of VDE portable equipment, and (120 Volt) UL544 non-patient medical equipment.
tyco Electronics Power PCB Relay RX
The document describes the features and characteristics of the products.
tyco Electronics AM-/AMC-/AMS-162 handbook
The document provides an introduction to the features and characteristics of a product.
TYCO ELECTRONICS AMP Commercial MATE-N-LOK Connectors handbook
This document provides the performance characteristics of tyco mate-n-lok connector, including voltage, current, withstand voltage, insulation resistance etc.
TYCO ELECTRONICS Toggle Switches AE Series Process Sealed Part Number Matrix handbook
This document is about the specification of Gemini series switches, including product dimensions, performance parameters, environmental temperature, etc.
TYCO ELECTRONICS SDE Options available Dies Tool Options handbook
This document provides price information for the Procrimper III tool, including price, model, and applicable wire size.
TYCO ELECTRONICS 4.2 mm PE Series Connector System Wire-to-Wire Wire-to-Board handbook
The document introduces a new product, including low-cost wire-to-wire and wire-to-board connectors suitable for computer motherboards/power supplies, harness assemblies used in the vending, gaming and appliance industries, car alarm systems, and heating systems. The product features easy mating and unmating with a positive latch design, offering 2-24 positions of receptacles, panel mount or free-hanging plugs, and vertical or right-angle pin headers. It is available in UL 94V-2 or UL 94V-0 flammability rated nylon, lead-free for environmental friendliness, and intermateable and interchangeable with Molex Mini-Fit, Jr. and AMP-DUAC connectors.