Atmel manuals, page 15
ATMEL ATmega8535 ATmega8535L Data Sheet
This document describes a high-performance, low-power AVR 8-bit microcontroller with advanced RISC architecture, including 130 powerful instructions, most of which can be executed in a single clock cycle. It has 8KB of in-system self-programmable flash and 512 bytes of EEPROM, as well as various peripheral features such as timers/counters, PWM channels, ADC, and serial interfaces.
ATMEL AT24C04B/AT24C08B Manual(1)
AT24C04B/08B is an 8-bit serial electrically erasable and programmable read-only memory (EEPROM) organized as 512/1024 words, each 8 bits. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The AT24C04B/08B is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead Ultra-Thin Mini-MAP (MLP 2x3), 5-lead SOT23, 8-lead TSSOP and 8-ball dBGA2 packages.
ATMEL AT45DB011D Preliminary Manual
The AT45DB011D is a 2.7V, serial-interface Flash memory ideally suited for a wide variety of digital voice-, image-, program code- and data-storage applications. The AT45DB011D supports RapidS serial interface for applications requiring very high speed operations. RapidS serial interface is SPI compatible for frequencies up to 66 MHz. Its 256 byte page size and flexible erase options make it ideal for large-capacity data storage applications. It also features low power consumption and high data retention.
ATMEL AT27C040 Manual
AT27C040 is a low-power, high-performance, OTP EPROM, organized as 512K*8 bits. This chip requires only one 5V power supply in normal read mode operation. Any byte can be accessed in less than 70ns, eliminating the need for speed reducing WAIT states on high-performance microprocessor systems. Atmel's scaled CMOS technology provides low active power consumption and fast programming. Power consumption is typically 8mA in active mode and less than 10µA in standby mode. AT27C040 is available in a choice of industry-standard JEDEC-approved one-time programmable (OTP) plastic PDIP, PLCC and TSOP packages. The device features two-line control (CE, OE) to eliminate bus contention in high-speed systems. Atmel's AT27C040 has additional features to ensure high quality and efficient production use. The Rapid Programming Algorithm reduces the time required to program the part and guarantees reliable programming. Typical programming time is 100µs/byte.
ATMEL 4-megabit 2.5-volt or 2.7-volt DataFlash AT45DB041D Manual
AT45DB041D is a 2.5V or 2.7V serial-interface Flash memory ideally suited for a wide variety of digital voice-, image-, program code- and data-storage applications. It features flexible erase options, low power dissipation, and hardware and software data protection features.
ATMEL AT45DB321D 32-megabit 2.7-volt DataFlash handbook
AT45DB321D is a 2.7-volt, serial-interface sequential access Flash memory ideally suited for a wide variety of digital voice-, image-, program code- and data-stor- age applications. The AT45DB321D supports RapidS serial interface for applications requiring very high speed.
ATMEL 4-megabit (512K x 8) 5-volt Only 256-byte Sector Flash Memory AT29C040A Manual
AT29C040A is a 5V in-system programmable and erasable read-only memory (PEROM) with features such as fast read access time, sector program operation, hardware and software data protection, etc.
ATMEL ATtiny13 Data Sheet
This document introduces the features of the ATtiny13 series of high-performance, low-power AVR® 8-bit microcontrollers, including advanced RISC architecture, non-volatile program and data storage, peripheral features, special microcontroller features, I/O and packaging, operating voltage, speed, etc.
ATMEL AT24C02B Two-wire Serial EEPROM Manual
AT24C02B is a 2K (2048 bits) serial electrically erasable and programmable read-only memory (EEPROM) produced by Microchip
ATMEL 8-bit AVR Microcontroller with 64K Bytes In-System Programmable Flash handbook
This document introduces the features and characteristics of ATmega8L88P
ATMEL AT24C32C AT24C64C handbook
The AT24C32C/64C is 32,768/65,536 bits of serial electrically erasable and programmable read only memory (EEPROM) organized as 4096/8192 words of 8 bits each. The device’s cascadable feature allows up to 8 devices to share a common 2- wire bus. The device is optimized for use in many industrial and commercial applications where low power and low voltage operation are essential.
ATMEL Two-wire Serial EEPROM AT24C1024B with Two Device Address Inputs Preliminary Manual
The document describes the features and characteristics of the AT24C1024B product, including low-voltage operation, internal organization, two-wire serial interface, Schmitt triggers, filtered inputs, bidirectional data transfer protocol, different clock rates, hardware and software data protection, page write mode, random and sequential read modes, self-timed write cycle, high reliability, etc.
ATMEL -AT89C5131 handbook
ATMEL -16-megabit (1M x 16/2M x 8) 3-volt Only Flash Memory AT49BV163D AT49BV163DT handbook
AT49BV163D(T) is a 2.7-volt 16-megabit Flash memory with features such as single voltage read/write operation, fast read access time, sector erase architecture, fast program and erase time.
ATMEL Three-wire Serial EEPROM 1K (128 x 8 or 64 x 16) AT93C46D Preliminary
AT93C46D is a 1024-bit serial electrically erasable programmable read-only memory (EEPROM), organized as 64 words of 16 bits each (when the ORG pin is connected to VCC), and 128 words of 8 bits each (when the ORG pin is tied to ground). The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operations are essential. AT93C46D is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead Ultra Thin mini-MAP (MLP 2x3), 8-lead TSSOP, and 8-lead dBGA2 packages. AT93C46D is enabled through the Chip Select pin (CS) and accessed via a three-wire serial interface consisting of Data Input (DI), Data Output (DO), and Shift Clock (SK). Upon receiving a Read instruction at DI, the address is decoded and the data is clocked out serially on the DO pin. The Write cycle is completely self-timed, and no separate Erase cycle is required before Write. The Write cycle is only enabled when the part is in the Erase/Write state.