ST Manuals

This document provides information on a product called L5300EPT, which is a low dropout linear regulator with a 5V output voltage, a current capability of 300mA, and a wide temperature range of -40°C to 150°C. It also features thermal shutdown and short-circuit protection.

This document introduces the features and characteristics of the VND5E050MJ-E and VND5E050MK-E dual-channel high-side drivers, including power management, input voltage, current detection, protection mechanisms, etc., which are suitable for various resistive, inductive and capacitive loads, and are also suitable for LED drivers

L5150GJ is a low dropout linear regulator with microprocessor control functions such as power on reset, low voltage reset, early warning, on/off control. Typical quiescent current is 55μA in very low output current mode and enabled regulator. It drops to 5μA with not enabled regulator. On chip trimming results in high output voltage accurancy (2%). Accurancy is kept over wide temperature range, line and load variation. Early warning circuit monitors the input voltage and compares it to an internal voltage reference. Output voltage reset threshold can be adjusted down to 3.5V by means of an external voltage divider. The maximum input voltage is 40V. The max output current is internally limited. Internal temperature protection disables the voltage regulator output. In addition, only low-value ceramic capacitor on output is required for stability.

L5150BN is a 5V low dropout linear regulator from ST. It has a wide operating voltage range (5.6V-40V), a low dropout voltage (500mV), a low quiescent current (50uA), and a high output voltage accuracy (±2%). It also has undervoltage protection, overcurrent protection, and overtemperature protection.

This datasheet provides information on the L99H01 product in full production. The L99H01 is a DC-motor driver for automotive applications that supports 6V to 28V, 100% duty cycle, and reverse battery protection MOSFET. It also supports PWM operation, SPI interface, and current sense amplifier.

This document is an instruction manual for VNN1NV04P-E, VNS1NV04P-E OMNIFET II fully autoprotected Power MOSFET, which introduces the characteristics of the product, including linear current limitation, thermal shutdown, short circuit protection, integrated clamp, low current from input pin, diagnostic feedback through input pin, ESD protection, direct access to the gate of the Power MOSFET (analog driving), etc.

This is a PDF document about VND5004B-E VND5004BSP30-E, it is a double 4mΩ high side driver with analog current sense for automotive applications. It has the following features: active power management, very low standby current, 3.0 V CMOS compatible input, optimized electromagnetic emission, very low electromagnetic susceptibility, in compliance with the 2002/95/EC European directive. Diagnostic functions include proportional load current sensing, current sense disable, thermal shutdown indication. Protection functions include undervoltage shutdown, overvoltage clamp, load current limiting, thermal shutdown, self limiting of fast thermal transients, protection against ground loss and loss of VCC, reverse battery protection with self switch on of the Power MOSFET (see Figure 22), electrostatic discharge protection application. Suitable for all types of resistive, inductive and capacitive loads, suitable for power management applications.

The VNH5019A-E is a full bridge motor driver from STMicroelectronics. The product has a 30A output current, uses ECOPACK® packaging, supports 3V CMOS compatible inputs, and integrates thermal shutdown functions on both the high and low sides. In addition, the product also has overvoltage protection, undervoltage protection, cross conduction protection, current limiting, extremely low standby power consumption, PWM operation, overcurrent protection, reverse polarity protection, etc.

VN5E010MH-E is a single-channel high-side driver manufactured in ST proprietary VIPower M0-5 technology and housed in the tiny HPAK package. The VN5E010MH-E is designed to drive 12 V automotive grounded loads delivering protection, diagnostics and easy 3 V and 5 V CMOS compatible interface with any microcontroller. The device integrates advanced protective functions such as short circuit protection, overvoltage protection, undervoltage shutdown, overcurrent protection and thermal shutdown.

This datasheet describes the features of the OMNIFET II fully autoprotected Power MOSFET VNN7NV04P-E and VNS7NV04P-E, including linear current limitation, thermal shutdown, short circuit protection, integrated clamp, low input pin current, diagnostic feedback, ESD protection, direct access to the gate of the Power MOSFET (analog driving) and compatibility with standard Power MOSFET in compliance with the 2002/95/EC European Directive.

This product is VNN3NV04P-E, VNS3NV04P-E OMNIFET II fully autoprotected Power MOSFET, which has linear current limitation, thermal shutdown, short circuit protection, integrated clamp, low input current, diagnostic feedback, ESD protection, direct access to MOSFET gate etc.

VN800PS-E High-side driver