intersil Manuals

The ISL59446 is a 500MHz bandwidth four-way quarter gain multiplexing amplifier from Intersil. It has a high gain, high speed and excellent bandwidth, and is suitable for video switching.

EL8108 is a video distribution amplifier from Intersil with high driving capability and low quiescent current.

The EL7156 is a high performance pin driver with three-state is suited to many ATE and level-shifting applications.

The HA4314B is a very wide bandwidth 4x1 crosspoint switch ideal for professional video switching, HDTV, computer monitor routing, and other high performance applications. The circuit features very low power dissipation (105mW Enabled, 4mW Disabled), excellent differential gain and phase, and very high off isolation. When disabled, the output is switched to a high impedance state, making the HA4314B ideal for routing matrix equipment. The HA4314B requires no external current source, and features fast switching and symmetric slew rates. For a 4x1 crosspoint with Tally outputs (channel indicators) or with synchronous control signals, please refer to the HA4404B and HA4344B data sheets, respectively. For audio channels requiring larger signal swings, please refer to the CD22M3494 (16x8) data sheet.

The ISL1539 is a dual channel differential VDSL2 line driver used for high performance long reach and high-speed applications. The driver has been optimized for flat gain response, reduced harmonic distortion, and noise to improve the overall signal to noise ratio in the system. The drivers achieve a total harmonic distortion (THD) measurement of typically -60dB MTPR @ 1.1MHz, while consuming typically 10mA per DSL channel of total supply current. The device operates on ±5V to ±15V supplies and retains its bandwidth and linearity over the complete supply range. It is supplied in a small footprint (4mmx5mm) 24 Ld QFN package and is specified for operation over the full -40°C to +85°C temperature range.

This document describes the features and characteristics of the PROFET BTS 432 F2 smart highside power switch produced by Infineon Technologies AG, including load dump and reverse battery protection, negative voltage clamp at the output, short-circuit protection, current limitation, thermal shutdown, diagnostic feedback, open load detection in ON-state, CMOS compatible input, electrostatic discharge (ESD) protection, loss of ground and loss of Vbb protection, overvoltage protection, and undervoltage and overvoltage shutdown with auto-restart and hysteresis. The product is a microcontroller compatible power switch with diagnostic feedback for 12V and 24V DC grounded loads, most suitable for inductive loads, and can replace electromechanical relays and discrete circuits.

This document describes the features and characteristics of Infineon Technologies AG's PROFET® BTS 432 F2 smart highside power switch, including load dump and reverse battery protection, negative voltage clamp at output, short-circuit protection, current limitation, thermal shutdown, diagnostic feedback, open load detection, CMOS compatible input, electrostatic discharge protection, loss of ground protection, overvoltage protection, undervoltage and overvoltage shutdown.

This is a high-end smart power switch with load dump and reverse battery protection, negative voltage clamp at output, short-circuit protection, current limitation, thermal shutdown, diagnostic feedback, open load detection, CMOS compatible input, electrostatic discharge (ESD) protection, ground loss and Vbb loss protection, overvoltage protection and other functions. It is suitable for 12V and 24V DC grounded loads of µC compatible power switch, and can replace electromechanical relays and discrete circuits.

SPP24N60C3 is a high voltage power transistor, its features are new revolutionary high voltage technology, worldwide best RDS(on) in TO220, ultra low gate charge, periodic avalanche rated, extreme dv/dt rated, ultra low effective capacitances and improved transconductance.

This datasheet provides information about SPP24N60C3, including maximum voltage, current and power consumption.

ISL6562 is a two-phase buck PWM controller for microprocessor CORE voltage regulation. This device together with companion gate drivers, HIP6601A, HIP6602A, HIP6603A or HIP6604 and MOSFETs provides a precision voltage regulation system for advanced microprocessors to satisfy the ever increasing current demands of modern microprocessors.

CA124, CA224, CA324, LM324, LM2902 are four independent high-gain operational amplifiers suitable for commercial, industrial, and military applications. They can be powered by single or dual supplies, and have low power consumption and a wide input common-mode voltage range.

CA158, CA158A, CA258, CA358, CA358A, CA2904, LM358, LM2904 are dual, 1MHz, operational amplifiers for commercial industrial, and military applications from the brand DINGHAO. They are designed specifically to operate from a single power supply over a wide range of voltages. They may also be operated from split power supplies.

CA139, CA139A, CA239, CA339, LM339, LM2901, LM3302 Quad Voltage Comparators for Industrial, Commercial and Military Applications. The devices in this series consist of four independent single or dual supply voltage comparators on a single monolithic substrate. The common mode input voltage range includes ground even when operated from a single supply, and the low power supply current drain makes these comparators suitable for battery operation. These types were designed to directly interface with TTL and CMOS. Type CA139A, has a lower input offset voltage than the CA139. Some of the SOIC parts are available on tape and reel (see Ordering Information table). Replace the M suffix in the part number with M96 when ordering (e.g., CA0239M96).