ANALOG Manuals

File format: PDF Size:0 KB

The AD9058 is a dual-channel 8-bit 50 MSPS analog-to-digital converter (ADC) with an integrated quadrature receiver. It features low input capacitance, high performance, and low power consumption.

File format: PDF Size:150 KB

The MAT03 is a low noise, matched dual PNP transistor with features such as low offset voltage, low noise, high gain, and high gain bandwidth. It is suitable for demanding preamplifier applications.

File format: PDF Size:576 KB

The AD775 is a CMOS, low power, 8-bit, 20 MSPS sampling analog-to-digital converter (ADC). The AD775 features a built-in sampling function and on-chip reference bias resistors to provide a complete 8-bit ADC solution. The AD775 utilizes a pipelined/ping pong two-step flash architecture to provide high sampling rates (up to 35 MHz) while maintaining very low power consumption (60 mW). Its combination of excellent DNL, fast sampling rate, low differential gain and phase errors, extremely low power dissipation, and single +5 V supply operation make it an ideal choice for various applications.

File format: PDF Size:333 KB

AD1849K is a serial-port 16-bit SoundPort® stereo codec with features including multiple channels of stereo input and output, digital signal mixing, on-chip speaker and headphone drive capability, programmable gain and attenuation, etc.

File format: PDF Size:232 KB

File format: PDF Size:1051 KB

The ADXL204 is a high precision, single-/dual-axis MEMS® accelerometer with ±1.7 g resolution, low power consumption, and is suitable for applications such as vehicle dynamic control (VDC)/electronic stability program (ESP) systems, electronic chassis controls, electronic braking, platform stabilization/leveling, navigation, alarms and motion detectors.

File format: PDF Size:559 KB

AD524 is a precision monolithic instrumentation amplifier designed by Analog Devices for data acquisition applications requiring high accuracy under worst-case operating conditions. It features outstanding combination of high linearity, high common mode rejection, low offset voltage drift, and low noise.

File format: PDF Size:349 KB

The AD976/AD976A is a high-speed, low-power 16-bit A/D converter that operates from a single 5V supply. The part contains a successive approximation, switched capacitor ADC, an internal 2.5V reference, and a high-speed parallel interface. The ADC is factory calibrated to minimize all linearity errors. The analog full-scale input is ±10V.

File format: PDF Size:180 KB

ADuC702x series is a precision analog microcontroller with 12-bit analog I/O and ARM7TDMI® MCU.

File format: PDF Size:858 KB

File format: PDF Size:424 KB

File format: PDF Size:0 KB

The ADXRS401 is a functionally complete and low cost angular rate sensor (gyroscope), integrated with all of the required electronics on one chip. It is manufactured using Analog Devices’ surface-micromachining technique, the same high volume BIMOS process used for high reliability. The ADXRS401 has a ±75°/s measurement accuracy, a Z-axis (yaw-rate) response, high vibration rejection over a wide frequency, 2000 g powered shock survivability, self-test on digital command, temperature sensor output, precision voltage reference output, absolute rate output for precision applications, 5 V single-supply operation, and is ultra small and light (< 0.15 cc, < 0.5 gram). It can be used for GPS navigation systems, image stabilization, inertial measurement units, and platform stabilization.

File format: PDF Size:404 KB

The AD592 is a two-terminal monolithic integrated circuit temperature transducer that provides an output current proportional to absolute temperature. It features high precision, excellent linearity, wide operating temperature range, single supply operation, and good repeatability and stability.

File format: PDF Size:303 KB

The AD8314 is a complete RF detector/controller for the measurement and control of RF signals in the frequency range of 0.1 GHz to 2.5 GHz. It has a typical dynamic range of 45 dB, excellent temperature stability, and provides a wider dynamic range and better accuracy than using discrete diode detectors.

File format: PDF Size:275 KB

The SSM2164 is a low-cost quad voltage controlled amplifier (VCA) that offers high performance and design flexibility. Each amplifier provides current input and output, as well as a ground referenced control port. It has high matching accuracy at unity gain and a gain range of 120 dB. It is suitable for cost-sensitive gain control applications.

File format: PDF Size:331 KB

File format: PDF Size:594 KB

The AD826 is a dual, high speed voltage feedback op amp. It is ideal for use in applications which require unity gain stability and high output drive capability, such as buffering and cable driving.

File format: PDF Size:259 KB

File format: PDF Size:283 KB

File format: PDF Size:494 KB