Manual for the Stanford Research Systems SR830 DSP lock-in amplifier, covering operation, specifications, programming, testing, and service information.
The SR830 is a DSP lock-in amplifier with signal, reference, and internal oscillator channels, plus displays, outputs, and auxiliary inputs and outputs. The manual covers safety and preparation, specifications, getting started, operating instructions, front and rear panel functions, programming commands, tests, circuitry, and parts lists.
It describes measurement quantities such as X, Y, R, and θ, time constants, dynamic reserve, filters, phase and frequency settings, data storage and transfer, and interface control through IEEE-488 and RS232.
| Voltage inputs | Single-ended (A) or differential (A-B) |
|---|---|
| Current input | 106 or 108 Volts/Amp |
| Full-scale sensitivity | 2 nV to 1 V |
| Input impedance (voltage) | 10 MΩ + 25 pF, AC or DC coupled |
| Gain accuracy | ±1% from 20°C to 30°C |
| Input noise | 6 nV/√Hz at 1 kHz (typical) |
| Signal filters | 60 (50) Hz and 120 (100) Hz notch filters (Q=4) |
| CMRR | 90 dB at 100 Hz (DC coupled) |
| Dynamic reserve | Greater than 100 dB |
| Harmonic distortion | -80 dB |
| Reference frequency range | 1 mHz to 102 kHz |
| Reference input | TTL or Sine |
| Phase resolution | 0.01° |
| Absolute phase error | <1° |
| Relative phase error | <0.01° |
| Orthogonality | 90° ± 0.001° |
| Harmonic detect | Nxf where N<19999 and Nxf<102 kHz |
| Acquisition time | (2 cycles + 5 ms) or 40 ms, whichever is greater |
| Time constants (reference > 200 Hz) | 10 µs to 30 s |
| Time constants (reference < 200 Hz) | up to 30000 s |
| Harmonic rejection | -80 dB |
| Internal oscillator frequency | 1 mHz to 102 kHz |
| Frequency accuracy | 25 ppm + 30 µHz |
| Frequency resolution | 4 1/2 digits or 0.1 mHz |
| Distortion | below -80 dBc below 10 kHz |
| Output impedance | 50 Ω |
| Oscillator amplitude | 4 mVrms to 5 Vrms |
| Amplitude accuracy | 1% |
| Amplitude stability | 50 ppm/°C |
| Channel display | 4 1/2 digit LED display with 40 segment LED bar graph |
| Offset | up to ±105% of full scale |
| Expand | by 10 or 100 |
| Data buffer | 16k points |
| Sample rate | 512 Hz down to 1 point every 16 seconds |
| Channel output voltage | ±10 V full scale |
| Channel output current | 10 mA max |
| Auxiliary output voltage | ±10.5 V full scale |
| Auxiliary input voltage | ±10.5 V full scale |
| Interfaces | IEEE-488 and RS232 |
| Power | 40 Watts, 100/120/220/240 VAC, 50/60 Hz |
| Dimensions | 17"W x 5.25"H x 19.5"D |
| Weight | 30 lbs |
| Warranty | One year parts and labor |
The voltage input impedance is 10 MΩ + 25 pF, AC or DC coupled.
IEEE-488 and RS232 interfaces are standard.
The SR830 uses 40 Watts from 100/120/220/240 VAC at 50/60 Hz.
The warranty is one year parts and labor on materials and workmanship.