Trex Transcend and Trex Enhance Composite Decking Technical Specifications

This document describes the physical and mechanical properties of the Trex Transcend and Trex Enhance products.


Trex Transcend and Trex Enhance Composite Decking Technical Specifications - cover page
Brand
TREX
Category
Other products
Document type
Product Leaflet
Language
English
Pages
7
File format
PDF
File size
82 KB
Published
16 November, 2023
Updated
16 November, 2023
MD5 checksum
DC86D25263DD3048480EDAC50C85AE65

About this manual

This Trex international architectural guide sets out technical specifications for Trex Transcend and Trex Enhance composite decking, focused on European physical and mechanical properties. Tables list the criterion, test method, result and a short explanation for bending modulus, breakage modulus, determination of slipperiness, fire resistance, creep behavior and falling mass impact resistance; the European laboratory tests were carried out by eph — Entwicklungs- und Pruflabor Holztechnologie GmbH in Dresden, Germany.

A second table gives general physical and mechanical properties tested to ASTM methods, including thermal expansion coefficient, compressive strength, relative density, resistance to fungal infestation, screw retention and water absorption, tested at Washington State University. The architectural specifier part covers references and design/performance requirements, submittals, delivery and storage, the limited residential and commercial warranty plus fade and stain terms, product data such as board size, lengths, colors and approved fasteners, and execution notes on cutting, drilling, routing and cleaning.

What's inside

  • European Physical & Mechanical Properties
  • Physical & Mechanical Properties
  • Architectural Specifier
  • Part 1: General — References and Design/Performance Requirements
  • Submittals, Delivery, Storage, and Handling
  • Warranty — Residential, Commercial, Fade and Stain
  • Part 2: Products — Manufacturers and Applications/Scope
  • Accessories and Fasteners
  • Part 3: Execution — Cutting, Drilling, Routing and Cleaning

Specifications

Bending Modulus (Transcend and Enhance, 25.4 mm)Deflection under load of 500 N ≤ 2.0 mm — Pass (PrEN 15534-1:2012)
Breakage Modulus (Transcend and Enhance, 25.4 mm)F' max ≥ 3300 N — Pass (PrEN 15534-1:2012)
Determination of Slipperiness — TranscendAverage angle of inclination 28, quality class C (wet-loaded barefooted areas, ramp test)
Determination of Slipperiness — EnhanceAverage angle of inclination 32, quality class C (wet-loaded barefooted areas, ramp test)
Fire Class — TranscendCfl - s1 according to EN 13501-1
Fire Class — EnhanceEfl according to EN 13501-1
Creep Behavior (Transcend and Enhance)Pass — 3-point bend under constant load of 850 N for 168 hr, must deflect less than 10 mm
Falling Mass Impact ResistancePass — 1000 g striker falling from 700 mm, 200 mm span, indentation ≤ 0.5 mm
Thermal Expansion Coefficient — Width8.94 x 10-5 cm/cm/C (ASTM D696)
Thermal Expansion Coefficient — Length4.1 x 10-5 cm/cm/C (ASTM D696)
Compressive Strength — Surface12.45 MPa (ASTM D695)
Compressive Strength — Edge13.40 MPa (ASTM D695)
Relative Density1.05 g/cm3 (ASTM D792)
Screw Retention1,377.25 N/m with #8 screws (ASTM D1761)
Board Size and Lengths (Transcend and Enhance)25 mm x 140 mm; lengths 3.66 m, 4.88 m, and 6.10 m

Frequently asked questions

What board size and lengths are Trex Transcend and Trex Enhance available in?

The planks are 25 mm x 140 mm and come in lengths of 3.66 m, 4.88 m, and 6.10 m.

What fire class do Trex Transcend and Trex Enhance achieve?

Under EN 13501-1, Transcend is Fire Class Cfl - s1 and Enhance is Fire Class Efl.

What warranty applies to Trex Transcend and Trex Enhance decking?

The limited warranty is twenty-five (25) years from the original purchase for a residential purchaser and ten (10) years for a commercial purchaser, plus fade and stain coverage for Transcend and Enhance.

Can Trex composite wood material be used for structural applications?

No. The document states that Trex composite wood material must not be used for structural applications.

Download PDF (82 KB)

More TREX Manuals


View all TREX manuals →