Einhell BT-BO 16/1 A 25/1 A 35/1 A Jumper Cable Operating Instructions

This is a user manual for a car jump starter cable.


Einhell BT-BO 16/1 A 25/1 A 35/1 A Jumper Cable Operating Instructions - cover page
Brand
EINHELL
Category
Car Accessories
Document type
User Manual
Language
German
Pages
28
File format
PDF
File size
735 KB
Published
31 October, 2023
Updated
31 October, 2023
MD5 checksum
C5C2D951E7A906B3C2FCE1B79B3A9F20

About this manual

This is the original operating instructions for the Einhell BT-BO 16/1 A, BT-BO 25/1 A and BT-BO 35/1 A jumper cables (article numbers 20.303.35, 20.303.45 and 20.303.25). The document explains what to check before jump starting, the order in which the red and black pole clamps are connected and removed, how long a starting attempt may take, and how to start a vehicle with a catalytic converter. It also notes the built-in overvoltage protection, which reduces sparking and whose LED indicates contact between the pole clamps and the battery terminals, plus general safety warnings about batteries and moving engine parts.

The technical data section lists cable cross-section, cable length and the engine sizes each of the three models is intended for, with 12 V or 24 V batteries. The manual closes with warranty terms, disposal notes for EU countries and the manufacturer's service addresses. The supplied text is in German; the printed document also contains English, French, Italian, Danish and Portuguese versions. This manual is written in German.

What's inside

  • Hinweis (safety notes and overvoltage protection)
  • Anklemmen (connecting the jumper cables)
  • Starten (starting the engine)
  • Abklemmen (disconnecting the jumper cables)
  • Hinweise: Starten von Katalysator-Autos
  • Technische Daten
  • Garantieurkunde
  • Recycling / Entsorgung

Specifications

Article numbers20.303.35, 20.303.45, 20.303.25
Cable cross-section (BT-BO 16/1 A)19.4 mm²
Cable length (BT-BO 16/1 A)3 m
Suitable engines (BT-BO 16/1 A)Petrol engines up to 2500 cc, 12 V or 24 V battery
Cable cross-section (BT-BO 25/1 A)31.4 mm²
Cable length (BT-BO 25/1 A)3.5 m
Suitable engines (BT-BO 25/1 A)Petrol engines up to 5500 cc or diesel engines up to 3000 cc
Cable cross-section (BT-BO 35/1 A)41 mm²
Cable length (BT-BO 35/1 A)4.5 m
Suitable engines (BT-BO 35/1 A)Petrol engines up to 7000 cc or diesel engines up to 4000 cc

Frequently asked questions

How do I connect the jumper cables?

Connect the red pole clamps first to the positive terminal of the discharged battery and then to the positive terminal of the donor battery. Then connect the black pole clamps to the negative terminal of the donor battery and finally to the vehicle ground of the broken-down car, as far from the battery as possible.

How long may one starting attempt take?

A starting attempt should not last longer than 15 seconds, and a waiting time of 1 minute must be observed afterwards.

What does the integrated overvoltage protection do?

It protects the vehicle electronics from harmful voltage peaks during jump starting and considerably reduces sparking. The LED built into its housing shows the contact of the pole clamps to the battery terminals.

When and in which order do I disconnect the jumper cables?

Once the engine runs smoothly, after 2 to 3 minutes, disconnect the cables in reverse order, starting with the black clamp on the ground of the broken-down vehicle.

Download PDF (735 KB)

More EINHELL Manuals


View all EINHELL manuals →