Industrial

The L296 is a high current switching regulator produced by Linear Technology, which can output 4A of current, with an output voltage range from 5.1V to 40V, supporting 0 to 100% duty cycle, precision of ±2%, switching frequency up to 200KHz, efficiency up to 90%, very few external components, soft start, reset output, external programmable limiting current (L296P), control circuit for Crowbar SCR, input for remote inhibit and synchronous PWM, and thermal shutdown.

The L200 is a monolithic integrated circuit for voltage and current programmable regulation. It is available in Pentawatt® package or 4-lead TO-3 metal case. Current limiting, power limiting, thermal shutdown and input overvoltage protection (up to 60 V) make the L200 virtually blow-out proof. The L200 can be used to replace fixed voltage regulators when high output voltage precision is required and eliminates the need to stock a range of fixed voltage regulators.

This document is a datasheet of L796BGD, which is a voltage regulator. It's a 3-terminal positive voltage regulator with a wide dropout voltage and low quiescent current. The output voltage is adjustable from 2.5V to 36V.

Introduction of ST2329B 2-bit dual supply level translator without direction control pin, open drain output

ST2149B 4-bit dual supply level translator without direction control pin datasheet.

ST2129B is a 2-bit dual supply level translator without direction control pin, push-pull output launched by ST. This product has 45MHz: 90Mbps (max.) data rate at VL = 1.8 V, VCC = 3.3 V, bi-directional level translation without direction control pin, wide voltage range (VL ≤ VCC): VL ranges from 1.65 to 3.6 V, VCC ranges from VL to 5.5 V, totem pole driving, 5.5 V tolerant Enable pin, ESD performance on all pins: ±2 kV HBM, small package and footprint QFN8 1.4 x 1.2 x 0.55 mm and other features.

This document describes a level translator for SD, SDIO, mini SD, and micro SD cards with internal I/O supply and ±15 kV ESD protection. It supports a clock rate of 60 MHz and DDR mode for SD Card™. It is compliant with SD Specification Part 1 Physical Layer Specification 3.00 (SDR12, SDR25, DDR50) and SD Specification Part 1 Physical Layer Specification 2.00. It is bi-directional with a direction control pin and has balanced propagation delays. It supports both 1.8 V and 2.9 V data translation on the card side and has an integrated LDO to supply power for B-side I/Os. It also has integrated pull-up and pull-down resistors on the B-side. The operating voltage range is VCCA = 1.62 V to 1.98 V and VBAT = 3.0 V to 5.0 V. It has latch-up performance exceeding 100 mA and ESD protection for both the card side and host side. It is available in a space-saving Flip Chip 25 package and is suitable for mobile phones, smartphones, PDAs, and cameras.

ST2329I is a 2-bit dual-supply level translator with auto-direction feature and integrated pull-up. It supports wide VL voltage range of 1.65 V to 3.6 V and wide VCC voltage range of 1.80 V to 5.5 V.

The STP16CPC26 is a monolithic, low voltage, 16-bit constant current LED sink driver, with 16 constant current output channels, adjustable output current through external resistor, output current: 5mA to 90mA, ±1% typical current accuracy bit to bit, max clock frequency: 30MHz, 20V current generators rated voltage, 5V power supply, thermal shutdown for overtemperature protection.

ST3DV520E is a 4 differential channel LVDS multiplexer/demultiplexer low RON bidirectional switch used to switch between multiple LVDS sources. It is designed for very low crosstalk, low bit-to-bit skew and low I/O capacitance, to maintain high signal integrity. The differential signal from the LVDS transceiver is multiplexed into one of two selected outputs while the unselected switch goes to Hi-Z status. The device integrates 2 SPDT (single pole dual throw) switches, for DDC channel. SEL for LVDS and DDC channel is controlled independently.

STG3696E is a low voltage dual SPDT switch for USB/audio signal switching with 8 kV ESD protection. It features low distortion negative signal swing capability for audio switch (range = VCC to VCC – 5.0 V), single supply operating voltage of VCC = 2.7 V to 4.5 V, typical bandwidth (–3 dB) of 950 MHz on all channels, USB (2.0) high speed (480 Mbps) signal switching compliant, integrated fail safe function to protect against short to 5.5 V, internal shunt resistors for pop noise suppression, auto detection of VBUS for switch selection, low RON resistance of 2.5 Ω (typ.), latch-up performance exceeds 100 mA per JESD 78, Class II, ESD performance exceeds JESD22 (COM pins to GND) ± 8 kV Human Body Model (A114-A), ESD performance exceeds JESD22 (other pins) ± 2 kV Human Body Model (A114-A). It is suitable for applications such as mobile phones, MP3 and other personal media players.

The STMPE1801 is a GPIO port expander capable of interfacing a main digital ASIC via the two-line bidirectional bus (I2C). It offers high flexibility, as each I/O can be configured as input, output, special key, keypad matrix, or dedicated key function. This device is designed to include very low quiescent current and a wakeup feature for each I/O to optimize power consumption. Potential applications include portable media players, game consoles, mobile phones, and smart phones.

The STLED325 is a compact LED controller/driver that interfaces microprocessors to LED displays through a serial I2C interface. It drives LEDs connected in a common anode configuration and includes keyscanning for an 8 x 2 key matrix, which automatically scans and debounces a matrix of up to 16 switches. Furthermore, the STLED325 provides standby power management to the host. It also integrates a low-power, highly accurate RTC and a remote control decoder. All functions are programmable using the I2C bus. Low power consumption during standby.

STMUX7000 is a 7-channel switch launched by ST company, which is mainly used for VGA signal switching. It has low RON, high ESD protection and low channel capacitance.

The STMPE1600 is a 16-bit port expander with ultra-low power consumption