Industrial Manuals

Chroma 8495 Electronic Ballast ATS Automatic Test System is specially designed for testing lighting electronic ballasts. It can support simultaneous testing of multiple / multiple outputs at a time to improve production line capacity. The standard test items optimized for electronic ballast characteristics have good test performance and meet the requirements of mass production.

SGDH series 200-350Amp capacitor throwing dedicated solid state relay is a new type of strip large power single-phase AC solid state relay for throwing capacitor of reactive compensation devices produced by Wei Hai Xing Jia Electronic Co., Ltd.

This document is the operation manual for the EJ1 modular temperature controller, providing information on its features, performance, and usage.

DL2,000TM DNA Marker is a DNA solution containing 1×Loading Buffer, which can be taken directly by 5μl electrophoresis, making it very convenient to use. DL2,000TM DNA Marker is composed of DNA fragments 2,000 bp, 1,000 bp, 750 bp, 500 bp, 250 bp and 100 bp, a total of 6 bands. When 5μl is taken for electrophoresis, the 750 bp DNA fragment is about 150 ng and shows a bright band. The DNA amount of the remaining bands is about 50 ng.

The stacked combination structure can be arbitrarily combined into a multi-beam interception system. The infrared wall is an efficient and reliable single-beam academic structure system. The intuitive LED/voltage indicates the alignment with the red alarm LED off. The detection distance is wide and the angle is adjustable. The outdoor 8 meters horizontal direction is 200 degrees vertical direction 10 degrees anti-disassembly protection normally closed contact ALC automatic gain control circuit surface shell can withstand high-intensity impact and prevent destruction. The unique optical system can reduce environmental stray light interference. It can penetrate dense fog or multiple transparent glass vertical barriers without being affected by user opening and closing windows. Optional accessories EX408 expansion module AH2 heating module installation instructions product features product features performance indicators performance indicators Model DS418 power supply 10-15VDC power consumption transmitter <10mA receiver <20mA application environment -25+55 RH35 90% -0+55 with attachment AH2-40+60 RH35 90% outdoor: 27 feet 8 meters control measurement mode infrared pulse beam status indication transmitter: red LED power indication receiver: red LED alarm indication alarm output C-type relay NC/NO anti-disassembly output NC optical system single beam optical axis horizontal adjustment 200 degrees optical axis vertical adjustment 20 degrees packaging size (HWL) 63 125 115mm product design is subject to change without notice product appearance diagram (µ¥Î»:mm) product appearance diagram (µ¥Î»:mm) installation position installation position diagram diagram single installation diagram recommended installation height is about 15cm multiple installation diagrams the following figure is an example of window installation installation instructions P/N: 4998134015B wiring diagram wiring diagram single detector wiring diagram multiple detector wiring diagram to control panel To Control Panel transmitter Transmitter receiver Receiver power supply Power anti-disassembly Tamper power supply Power anti-disassembly Tamper EOL to control panel To Control Panel power supply Power anti-disassembly Tamper transmitter Transmitter receiver Receiver EOL Figure 3 Figure 2 Figure 1 installation Mount the connected mounting backplate to the wall at the installation location using the screws and triangular plate provided with the accessory. Connect the wires through the inlet and outlet as shown in the figure. The appearance of the product is exquisite and the structure is compact. Please install it according to the provided methods to achieve the best effect. Figure 3 Figure 2 Figure 1 Two installation steps The wire heads left at the wiring end should be connected according to the figure without leaving them too long and press them under the film. Install the bottom shell with the backplate fixed by screws at the transmitter end and fix it with screws. Install the light reduction mask and adjust the optical horizontal and vertical angles of the transmitter and receiver until the alarm indicator light is off. Use a multimeter to measure the voltage of MJ1 and MJ2 ends. The voltage should be above 0.2V (2.5V gear) from top to bottom. Install the top cover until it is in place. Adjust the screw in the azimuth direction of the adjusting frame of the elevation angle. Light reduction plate triangular plate outlet hole power alarm cable inlet wire down to the next level power alarm cable power alarm cable stripping 10mm One installation step Figure 7 Figure Figure 6 Figure 5 Figure 4 From top to bottom, install the bottom shell with the threaded wire in the following order and fix it with screws at A. Press it tightly inside and push it up and tighten it with screws B. Install the shell and top cover from bottom to top, paying attention to the groove of the shell should be aligned with the bottom shell.

SJ-RC161 platinum resistance temperature sensor works on the principle that the resistance of the thin film platinum resistance changes with the temperature, and the relationship between resistance and temperature (i.e., the division characteristic) is completely the same as the IEC standard. At the same time, the platinum resistance sensor has good long-term stability. If the temperature transmitter is matched, it can output 4～20mA or other standard signals, which is more convenient to use. SJ-RC161 platinum resistance temperature sensor adopts three-wire lead-out method, which can effectively compensate the measurement error caused by lead resistance in combination with temperature transmitter.

This document is a user manual for SJ-RD161 temperature and humidity transmitter, which introduces the overview, technical parameters, dimensions, installation and wiring terminals, precautions and other information of the product.

The SD1500 series asynchronous data serial server is a product produced by Shanghai Yuling Communication Equipment Co., Ltd. This series of products has the features of supporting subnet mask, UDP protocol, and Break signal. It also supports TFTP and Advanced Management. The document also introduces the use of SD1501/SD1502Lite.

SD1500 series serial data network server quick configuration guide, introduces the product structure, configuration methods, and provides relevant download links

The QFK5F-45(63)-0.4(0.23) series switching capacitor composite switch is suitable for low-voltage three-phase common compensation single-phase compensation reactive compensation of capacitor switching control. It adopts a thyristor and a contactor in parallel. When the switch is on, it has the characteristic of thyristor zero-crossing instantaneous switching, and when it is normally closed, it has the characteristic of contactor suction. It has the advantages of no surge on capacitor and higher capacitor life. It has overcurrent protection, voltage and current display functions.

PT5622 is a dedicated control chip for electronic ballasts, suitable for dimming products with ordinary switches. It features lamp current negative feedback control, programmable preheating time and frequency, etc.

Y76DSH is a high power ultra fast semiconductor switch produced by Tech-Sem. Its main features are nanosecond turn-on speed, extremely high pulse output current, and no damage, long life.

MAX4854 is a 4-way single-pole/single-throw switch that is powered by a single supply of +2V to +5.5V and can handle signals that are greater than the supply swing. The switch has a low on-resistance and low on-capacitance, making it ideal for data signal switching. For over-range applications, signals that are greater than the positive supply (up to +5.5V) can still pass through the switch without distortion. MAX4854 is housed in a space-saving, 16-pin, 3mm x 3mm thin QFN package and operates in an extended temperature range of -40°C to +85°C.

This document is a application note of MAX8570ELT+T,MAX8570EUT+T,MAX8571EUT+T chips