UNITRODE manuals, page 7
Unitrode Products UCC1800/1/2/3/4/5 UCC2800/1/2/3/4/5 UCC3800/1/2/3/4/5 handbook
UCC1800/1/2/3/4/5 is a high-speed, low-power integrated circuit that contains all of the control and drive components required for off-line and DC-to-DC fixed frequency current-mode switching power supplies with minimal parts count.
UNITRODE UCC1581 UCC2581 UCC3581 handbook
UCC3581 is a voltage mode pulse width modulator designed to control low power isolated DC-DC converters, primarily used for single switch forward and flyback converters. It features BiCMOS circuitry for low startup and operating current, while being able to drive power MOSFETs at frequencies up to 100kHz. The UCC3581 oscillator allows programming of both the frequency and the maximum duty cycle with two resistors and a capacitor. It includes programmable soft start circuitry, overcurrent detection, a 7.5V linear preregulator for controlling chip VDD during startup, and an on-board 4.0V logic supply. The UCC3581 provides functions to maximize light load efficiency that are not normally found in PWM controllers.
UNITRODE UCC1583 UCC2583 UCC3583 handbook
UNITRODE UCC15701/2 UCC25701/2 UCC35701/2 handbook(1)
UCC15701/2 UCC25701/2 UCC35701/2 is Advanced Voltage Mode Pulse Width Modulator
UNITRODE UCC15701/2 UCC25701/2 UCC35701/2 handbook
UCC15701/2 UCC25701/2 UCC35701/2 Advanced Voltage Mode Pulse Width Modulator
UNITRODE UCC1570 UCC2570 UCC3570 handbook(1)
The UCC1570 family of pulse width modulators is intended for application in isolated switching supplies using primary side control and a voltage mode feedback loop. Made with a BiCMOS process, these devices feature low startup current for efficient off-line starting with a bootstrapped low voltage supply. Operating current is also very low; yet these devices maintain the ability to drive a power MOSFET gate at frequencies above 500kHz. Voltage feedforward provides fast and accurate response to wide line voltage variation without the noise sensitivity of current mode control. Fast current limiting is included with the ability to latch off after a programmable number of repetitive faults has occurred. This allows the power supply to ride through a temporary overload, while still shutting down in the event of a permanent fault. Additional versatility is provided with a maximum duty cycle clamp programmable within a 20% to 80% range and line voltage sensing with a programmable window of allowable operation.
UNITRODE UCC1570 UCC2570 UCC3570 handbook
UNITRODE UCC1580-1/-2/-3/-4 UCC2580-1/-2/-3/-4 UCC3580-1/-2/-3/-4 handbook(2)
The UCC3580 family of PWM controllers is designed to implement a variety of active clamp/reset and synchronous rectifier switching converter topologies. It includes an auxiliary switch driver that complements the main power switch and has a programmable deadtime or delay between each transition. The features of this product family include voltage mode control, programmable limits for transformer volt-second product and PWM duty cycle, high current gate driver, multiple protection features, and low supply current.
UNITRODE UCC1580-1/-2/-3/-4 UCC2580-1/-2/-3/-4 UCC3580-1/-2/-3/-4 handbook(1)
The document is the datasheet of UCC1580-1,-2,-3,-4 UCC2580-1,-2,-3,-4 UCC3580-1,-2,-3,-4 PWM controllers, introducing the features and characteristics of the product.
UNITRODE UCC1580-1/-2/-3/-4 UCC2580-1/-2/-3/-4 UCC3580-1/-2/-3/-4 handbook
The UCC3580 family of PWM controllers is designed to implement a variety of active clamp/reset and synchronous rectifier switching converter topologies. While containing all the necessary functions for fixed frequency, high performance pulse width modulation, the additional feature of this design is the inclusion of an auxiliary switch driver which complements the main power switch, and with a programmable deadtime or delay between each transition. The active clamp/reset technique allows operation of single ended converters beyond 50% duty cycle while reducing voltage stresses on the switches, and allows a greater flux swing for the power transformer. This approach also allows a reduction in switching losses by recovering energy stored in parasitic elements such as leakage inductance and switch capacitance. The oscillator is programmed with two resistors and a capacitor to set switching frequency.
UNITRODE bq2011 handbook
UNITRODE bq2010 handbook
The document introduces the characteristics of bq2010 gas gauge ic. bq2010 gas gauge ic can detect the battery charge in charging and discharging state, and estimate the self-discharge current of the battery using the internal temperature sensor and timer. Finally, the available charge of the battery is calculated. The ic can also display the available charge of the battery via a 5-segment or 6-segment led display.
UNITRODE bq2007 handbook
bq2007 is a highly integrated monolithic CMOS IC designed to provide intelligent battery charging and charge status monitoring for stand-alone charge systems.
UNITRODE bq2005 handbook
The document describes the features and characteristics of the bq2005 Fast-Charge IC, including sequential fast charge and conditioning of two NiCd or NiMH battery packs, hysteric PWM switch-mode current regulation or gated control of an external regulator, easy integration into systems or use as a stand-alone charger, pre-charge qualification of temperature and voltage, direct LED outputs display battery and charge status, fast-charge termination by ∆ temperature/∆ time, -∆V, maximum voltage, maximum temperature, and maximum time, optional top-off and pulse-trickle charging.
UNITRODE bq2004E/H handbook(1)
bq2004e/h fast charge ic integrates closed-loop current control circuitry, making it a cost-effective solution for stand-alone and system-integrated chargers for batteries of one or more cells.