MXIC Manuals

Key facts

Manuals

24

Models

1

Languages

EN

Last added

2012-06-12

MXIC models by category

Featured MXIC manuals

Macronix MX93000 Special Codec Datasheet

Datasheet 24 pages · 186 KB · EN

The MX93000 Special Codec is a single‑chip solution for digital answering machine (DAM) systems, requiring only a +5 V supply. It combines sigma‑delta A/D and D/A converters, on‑chip automatic level control, programmable gain amplifier, and a fully differential line driver, allowing direct connection to telephone lines without external amplifiers.

The device offers extensive configurability through programmable registers, supporting multiple signal paths, volume control, and power‑down detection. Detailed specifications cover analog input/output ranges, gain steps, dynamic range, noise performance, and power consumption.

Covers: Features · Pin Configuration · Product Overview · Functional Description · Automatic Level Control · Serial Control Interface

Latest MXIC manuals

• MXIC MX9691 DATA SHEET

  This document introduces a PCMCIA interface product that is fully compatible with PCMCIA Release 2.1 and PC Card ATA Release 1.02 specifications. It supports fast ATA host-to-buffer burst transfer rates up to 20MB/sec, with automatic sensing of PCMCIA or ATA host interface. The product features integrated PCMCIA attribute memory, PCMCIA card configuration register support, polarity control for host reset signal, PCMCIA twin card support, PCMCIA based ATA address decode support, and emulation of the IBM task file for PC/AT. It also provides a flash memory interface with support for read/write/erase operations, up to 32MB or 64MB capacity, flash memory power down or write protect control, flash memory ready/busy status detection, inverted data bus control, and optional storage of firmware in flash memory array with shadow ROM control.

• MXIC MX27L1000 DATA SHEET

  The MX27L1000 is a 1M-bit, One Time Programmable Read Only Memory. It is organized as 128K words by 8 bits per word, operates from a single 2.7 to 3.6 volt supply, has a static standby mode, and features fast single address location programming. All programming signals are TTL levels, requiring a single pulse. For programming outside from the system, existing EPROM programmers can be used.

• MXIC MX23L12811 DATA SHEET

  MX23L12811 is a 8M x 16-bit mask ROM with page mode (SOP only). It features random access time of 90ns (max.), page access time of 25ns (max.), and page size of 8 words per page. The pin configuration is 44 SOP (Word Mode Only).

• MXIC MX27C512 DATA SHEET

• MXIC MX23C6410 handbook

  MX23C6410 is a 64M-BIT Mask ROM, with 8M x 8 bit organization and 100ns random access time. It is available in 44 pin SOP and 48 pin TSOP packages.

• MXIC MX27C256 Data Sheet

  MX27C256 is a 5V only, 256K-bit, ultraviolet erasable programmable read only memory. It is organized as 32K by 8 bits, operates from a single + 5volt supply, has a static standby mode, and features fast single address location programming.

• MXIC MX10E8050I Data Sheet

  This document describes the features and characteristics of the MX10E8050I series products, including 80C51 CPU core, voltage range of 3.0 ~ 3.6V, on-chip Flash program memory with in-system programming (ISP), etc.

• MXIC MX27C1000A DATA SHEET

  The MX27C1000A is a 5V-only, 1M-bit, One Time Programmable Read Only Memory. It is organized as 128K words by 8 bits per word, operates from a single +5 volt supply, has a static standby mode, and features fast single address location programming.

• MXIC MX29LA128MT/B handbook

  MX29LA128M T/B is a 128M-BIT single voltage 3V flash memory with features like single power supply operation, switchable configuration, multiple sector structure, high performance, low power consumption, and support for CFI interface.

• MXIC MX29F400MT/B handbook

  MX29F400T/B is a 4M-bit CMOS FLASH memory with 512Kx8/256Kx16 bit organization. It provides a fast access time of 55/70/90/120ns, and low power consumption of 40mA maximum active current(5MHz) and 1uA typical standby current. The Ready/Busy pin provides a hardware method of detecting program or erase cycle completion. It also supports sector protection and 100,000 minimum erase/program cycles.

• MXIC MX29F040 Data Sheet

  The MX29F040 is a 4-mega bit Flash memory organized as 512K bytes of 8 bits. MXIC's Flash memories offer the most cost-effective solutions to meet the needs of various applications.

• MXIC MX27L2000 Data Sheet

  The MX27L2000 is a 3V only, 2M-bit, One Time Programmable Read Only Memory. Its features are 256K words by 8 bits per word, 2.7V DC to 3.6V DC, +12.5V, 120/150/200/250 ns, static standby mode, completely TTL compatible, 20mA @ 3.6V, 5MHz.

• MXIC MX29LV004T/B handbook

  This document describes the features and characteristics of a 4M-BIT single voltage 3V flash memory called MX29LV004T/B, including status reply, ready/busy pin, sector protection, minimum erase/program cycles, latch-up protection, boot sector architecture, low VCC write inhibit, and package type.

• MXIC MX27C512 handbook

  The MX27C512 is a 5V only, 512K-bit, ultraviolet Eras- able Programmable Read Only Memory. It is organized as 64K words by 8 bits per word, operates from a single +5volt supply, has a static standby mode, and features fast single address location programming.

• MXIC MX23L2000 handbook

  This document is a specification for the MX23L2000 2M-bit MASK ROM chip. The chip features a bit organization of 256K x 8, fast access time of 150ns, low power consumption, and a supply voltage range of 2.7V to 3.6V.

Which document do I need?

Questions answered in MXIC manuals