The DS2107A SCSI Terminator provides active termination for 9 signal lines and is fully compliant with SCSI and SCSI-2 standards. It is backward compatible with the DS2107S.
The DS2106 is a fully compliant SCSI-1, Fast SCSI and Ultra SCSI SCSI terminator. It functionally compatible with DS21S07A, providing active termination for 18 signal lines. The termination resistors and voltage regulator are within 5% tolerance, the termination current is within 5% tolerance, the power down capacitance is 3 pF, and there is on-board thermal shutdown circuitry. It is compatible with hot plug of SCSI bus and fully supports actively negated SCSI signals.
The DS2105 SCSI Terminator is a terminator that complies with SCSI–1, Fast SCSI, and Ultra SCSI standards. It provides active termination for nine signal lines. The terminator has features such as low dropout voltage, support for actively negated SCSI signals, onboard thermal shutdown circuitry, and a 16-pin plastic SOIC package.
DS1963S is a financial iButton with SHA-1 functionality and a 4k-bit read/write data area. It has a 4096-bit non-volatile (NV) memory, divided into 16 pages of 256 bits each. It also features independent 64-bit keys and 32-bit read-only, non-rolling page write counters. The device also includes a 512-bit SHA-1 engine that can calculate a 160-bit message authentication code (MAC) and can be used as a co-processor for roaming iButtons or hosts.
The DS2016 2k x 8 3V/5V Operation Static RAM is a 16,384-bit, low-power, fully static random access memory organized as 2048 words by 8 bits using CMOS technology. The device operates from a single power supply with a voltage input between 2.7 and 5.5 volts. The chip enable input ( CE ) is used for device selection and can be used in order to achieve the minimum standby current mode, which facilitates both battery operated and battery backup applications. The device provides access times as fast as 100 ns when operated from a 5-volt power supply input and also provides relatively good performance of 250 ns ac.
This datasheet provides information on the DS4802's features and specifications, including very low power consumption, high output current, a 1.8V to 5.5V supply voltage range, a voltage range of 0.95mV for the input offset voltage, a maximum IDD of 25µA and a typical input bias current of 10pA, making it ideal for measurement, medical and industrial applications.
The DS2438 is a smart battery monitor that provides several functions, including tagging a battery pack with a unique serial number, measuring battery voltage and current, calculating battery capacity, and measuring battery temperature.
This document describes a complete E1, T1, or J1 line interface unit (LIU) that supports both long- and short-haul trunks. It features internal software-selectable receive-side termination, multiple clock outputs, and encoding/decoding capabilities.
The DS1742 is a full-function, Y2KC-compliant, real-time clock/calendar (RTC) and 2k x 8 non-volatile static RAM. User access to all registers within the DS1742 is accomplished with a bytewide interface as shown in Figure 1. The Real Time Clock (RTC) information and control bits reside in the eight uppermost RAM locations. The RTC registers co-exist with the static RAM registers in the same address space, but cannot be accessed simultaneously.
The document describes the features and characteristics of the DS1855 series products, including two linear taper potentiometers, 256 bytes of EEPROM memory, 2-wire interface, etc.
The DS1847 is a temperature controlled variable resistor from Texas Instruments, which has two linear variable resistors. The resistors can be changed every 2°C in the range of -40°C to +95°C. The device can access temperature data and device control via a 2-wire serial bus.
The DS1135 series is a low-power, +5-volt high-speed version of the popular DS1013 and DS1035. The DS1135 series of delay lines have three independent logic buffered delays in a single package. The device features precise leading and trailing edge accuracy. It has the inherent reliability of an all-silicon delay line solution. Each output is capable of driving up to 10 LS loads. Standard delay values are indicated in Table 1.
The DS1624 is a digital thermometer and memory device that provides 13-bit temperature readings and 256 bytes of E2 memory for storing frequency compensation coefficients.
