National Semiconductor manuals, page 14
National Semiconductor LMH6550 Differential High Speed Op Amp handbook
The LMH6550 is a high-performance voltage feedback differential amplifier with high speed and low distortion, suitable for driving high-performance ADCs and signals over balanced transmission lines such as CAT 5 data cables. It can handle a wide range of video and data formats and can be used at any desired gain with external gain set resistors. The LMH6550 is suitable for applications such as IF amplifiers in high-performance communications equipment.
National Semiconductor LMH6533 Four Channel Laser Diode Driver with Dual Output LVDS Interface HFM Oscillator handbook
National Semiconductor LMH6505 Wideband Low Power Linear-in-dB Variable Gain Amplifier handbook
LMH6505 is a wideband, low power, linear-in-dB, variable gain amplifier from Texas Instruments. This device uses a voltage controlled gain stage followed by a high-speed current feedback op amp that can directly drive a low impedance load. LMH6505's gain adjustment range is 80 dB for up to 10 MHz.
National Semiconductor LMH6504 Wideband Low Power Variable Gain Amplifier handbook
LMH6504 is a wideband, low power, variable gain amplifier. It has a gain adjustment range of 80 dB up to 10 MHz by varying the gain control input voltage. The maximum gain is set by external components, and the gain can be reduced to cut-off. The power consumption is 110 mW with a speed of 150 MHz and a gain control bandwidth of 150 MHz. The output referred DC offset voltage is less than 55 mV over the entire gain control voltage range. Device-to-device gain matching is within ±0.42 dB at maximum gain.
National Semiconductor LMH6502 Wideband Low Power Linear-in-dB Variable Gain Amplifier handbook
LMH6502 is a wideband, low power, linear-in-dB variable gain amplifier
National Semiconductor LMH1251 YPBPR to RGB Decoder 2:1 Video Switch handbook
LMH1251 is a wideband 2:1 analog video switch with an integrated YPBPR to RGB decoder
National Semiconductor LMH0034 SMPTE 292M 259M Adaptive Cable Equalizer handbook
The LMH0034 is a monolithic integrated circuit that can be used to equalize data transmitted over a cable (or any media with similar dispersive loss characteristics) at data rates from 143 Mbps to 1.485 Gbps. It supports the SMPTE 292M, SMPTE 344M and SMPTE 259M standards. The LMH0034 implements DC restoration to correctly handle pathological data conditions. DC restoration can be bypassed for low data rate applications. The equalizer is flexible in allowing either single-ended or differential input drive. Additional features include a combined carrier detect and output mute pin which mutes the output when no signal is present. A programmable mute reference is used to mute the output at a selectable level of signal degradation. A cable length indicator is provided to determine the amount of cable being equalized.
National Semiconductor LMH0002 SMPTE 292M 259M Serial Digital Cable Driver handbook
The LMH0002 is a high-performance cable driver from National Semiconductor Corporation that complies with the SMPTE 292M / 259M standard. It supports 75-ohm transmission lines and has a transmission speed of up to 1.485 Gbps. The LMH0002 provides two selectable slew rates to meet SMPTE 259M and SMPTE 292M standards. The output voltage swing can be adjusted via a single external resistor. The LMH0002 is powered by a single 3.3V supply. Typical power consumption is 125mW (SD mode) and 149mW (HD mode).
National Semiconductor LP5990 Micropower 200mA CMOS Low Dropout Voltage Regulator General Description The LP5990 regulator is designed to meet the requirements of portable battery-powered systems pr
National semiconductor LP5900 Ultra Low Noise 100 mA Linear Regulator for RF/Analog Circuits Requires No Bypass Capacitor handbook
The LP5900 is a linear regulator capable of supplying 100 mA output current. Designed to meet the requirements of RF/Analog circuits, the LP5900 device provides low noise, high PSRR, low quiescent current, and low line transient response figures. Using new innovative design techniques the LP5900 offers class-leading device noise performance without a noise bypass capacitor. The device is designed to work with 0.47 µF input and output ceramic capacitors. (No Bypass Capacitor is required) This device is available with 1.5V, 1.8V, 2.0V, 2.2V, 2.5V, 2.8V, 3.0V, and 3.3V outputs.
National semiconductor LP5550 PowerWise Technology Compliant Energy Management Unit handbook
The LP5550 is a PWI 1.0 compliant Energy Management System for reducing power consumption of stand-alone mobile phone processors such as base-band or applications processors. The LP5550 contains an advanced, digitally controlled switching regulator for supplying variable voltage to processor core and memory. The device also incorporates 3 programmable LDO-regulators for powering I/O, PLLs and maintaining memory retention in shutdown-mode. The device is controlled via the PWI open-standard interface. The LP5550 operates cooperatively with PowerWise technology compatible processors to optimize supply voltages adaptively over process and temperature variations or dynamically using frequency/voltage pre-characterized look-up tables.
National Semiconductor LM10 Operational Amplifier Voltage Reference handbook
LM10 is a voltage reference and operational amplifier produced by Texas Instruments
National Semiconductor LM1085 3A Low Dropout Positive Regulators handbook
This document introduces the features of the LM1085 series low dropout positive voltage regulators, including adjustable and fixed versions, which can provide 3.3V, 5.0V and 12.0V output voltages, with current limiting and thermal protection.
National Semiconductor LM1084 5A Low Dropout Positive Regulators handbook
National LM1042 handbook
The LM1042 is a fluid level detector that uses a thermal-resistive probe technique to measure the level of non-flammable fluids. It provides an output signal proportional to the fluid level and supports single-shot or repeating measurements. The device incorporates all the necessary control circuitry for the thermal-resistive probe, including short and open circuit probe detection. It also features a second linear input for alternative sensor signals.