Maxim manuals, page 94
MAXIM MAX9075/MAX9077 Manual
This datasheet introduces the MAX9075/MAX9077 single/dual comparators, which are optimized for 3V and 5V single-supply applications. These comparators have a 580ns propagation delay and consume just 3µA per comparator. The combination of low-power, single-supply operation down to 2.1V, and ultra-small footprint makes these devices ideal for all portable applications.
MAXIM MAX9140/MAX9141/MAX9142/MAX9144 Manual
The MAX9140/MAX9141/MAX9142/MAX9144 are high-speed comparators with high speed, low power, and rail-to-rail inputs. Propagation delay is 40ns, while supply current is only 150µA per comparator. The MAX9140/MAX9141/MAX9142/MAX9144's input common-mode range extends beyond both power-supply rails. The outputs pull to within 0.3V of either supply rail without external pullup circuitry, making these devices ideal for interface with both CMOS and TTL logic. All input and output pins can tolerate a continuous short-circuit fault condition to either rail. Internal hysteresis ensures clean output switching, even with slow-moving input signals. The MAX9140/MAX9141/MAX9142/MAX9144 are higher-speed, lower-power, and lower-cost upgrades to industry-standard comparators MAX941/MAX942/MAX944. The MAX9140 are offered in tiny 5-pin SC70 and SOT23 packages. The MAX9141 and MAX9142 are available in 8-pin SOT23 and SO packages, while the MAX9144 is available in both 14-pin SO and TSSOP packages.
MAXIM AX9060 MAX9064 Manual
MAX9060 series products are a kind of miniature single comparators produced by Texas Instruments. They are very suitable for a wide range of portable electronic applications such as cell phones, media players and notebooks which have extremely tight board space and power constraints. The series products provide ultra-miniature 4-bump UCSP package with a 1mm x 1mm footprint (as small as two 0402 resistors); and also provide 5-pin SOT23 package. The series products feature an input voltage range of -0.3V to +5.5V independent of supply voltage. These devices maintain high impedance at the inputs even when powered down (VCC or VREF = 0V). They also feature internal filtering to provide high RF immunity. MAX9060 and MAX9061 have open-drain outputs and draw quiescent supply current from a user-supplied reference voltage, VREF, between 0.9V and 5.5V. These devices consume only 100nA (max) supply current and operate over the extended -40°C to +85°C temperature range. MAX9062, MAX9063 and MAX9064 are single com- parators with an internal 0.2V reference. These devices feature either a push-pull or an open-drain output. They consume only 700nA (max) supply current. The MAX9062, MAX9063, and MAX9064 operate down to VCC = 1V over the extended -40°C to +85°C temperature range.
MAXIM MAX9025 MAX9028 Manual
The MAX9025-MAX9028 ultra-low-power comparators are integrated circuits in a space-saving chip-scale (UCSP) package with Beyond-the-Rails inputs that are guaranteed to operate down to +1.8V. The MAX9025/MAX9026 feature an on-board 1.236V ±1% reference and draw an ultra-low supply current of only 1µA, while the MAX9027/MAX9028 (without reference) require just 0.6µA of supply current. These features make the MAX9025-MAX9028 family of comparators ideal for all 2-cell battery-monitoring/management applications. The unique design of the output stage limits supply-current surges while switching, virtually eliminating the supply glitches typical of many other comparators. This design also minimizes overall power consumption under dynamic conditions. The MAX9025/MAX9027 have a push-pull output stage that sinks and sources current. Large internal-output drivers allow rail-to-rail output swing with loads up to 5mA. The MAX9026/MAX9028 have an open-drain output stage that makes them suitable for mixed-voltage system design. All devices are available in the miniature 6-bump UCSP packages. For similar comparators in 5-pin SC70 packages, refer to the MAX9117 data sheet, and for similar dual comparators in 8-pin SOT23 packages, refer to the MAX9017 data sheet. Applications include 2-cell battery monitoring/management, ultra-low-power systems, mobile communications, notebooks and PDAs, sensing at ground or supply line, telemetry and remote systems, and medical instruments.
MAXIM MAX9021/MAX9022/MAX9024 Manual
The MAX9021/MAX9022/MAX9024 is a low-power comparator that operates from a single supply from 2.5V to 5.5V, and consumes 2.8µA of supply current per comparator. It has a 3µs propagation delay and 4mV of built-in hysteresis to provide noise immunity and prevent oscillations.
MAXIM MAX985/MAX986/MAX989/MAX990/MAX993/MAX994 Manual
The MAX985/MAX986/MAX989/MAX990/MAX993/MAX994 single/dual/quad micropower comparators feature low-voltage operation and rail-to-rail inputs and outputs. Their operating voltages range from 2.5V to 5.5V, making them ideal for both 3V and 5V systems. These comparators also operate with ±1.25V to ±2.75V dual supplies. They consume only 11µA of supply cur- rent while achieving a 300ns propagation delay. Input bias current is typically 1.0pA, and input offset voltage is typically 0.5mV. Internal hysteresis ensures clean output switching, even with slow-moving input signals. The output stage’s unique design limits supply-current surges while switching, virtually eliminating the supply glitches typical of many other comparators. The MAX985/MAX989/MAX993 have a push-pull output stage that sinks as well as sources current. Large inter- nal output drivers allow rail-to-rail output swing with loads up to 8mA. The MAX986/MAX990/MAX994 have an open-drain output stage that can be pulled beyond VCC to 6V (max) above VEE. These open-drain versions are ideal for level translators and bipolar to single- ended converters. The single MAX985 is available in a chip-scale pack- age (UCSP™), significantly reducing the required PC board area. The single MAX985/MAX986 are available in 5-pin SC70 packages and the dual MAX989/MAX990 are available in 8-pin SOT23 packages.
MAXIM MAX9030/MAX9031/MAX9032/MAX9034 Manual
MAXIM MAX9107/MAX9108/MAX9109 Manual
MAX9107/MAX9108/MAX9109 25ns, Dual/Quad/Single, Low-Power, TTL Comparators are high-speed, low-power voltage comparators designed for use in systems powered from a single +5V supply. Their 25ns propagation delay (with 10mV input overdrive) is achieved with a power consumption of only 1.75mW per comparator. The wide input common-mode range extends from 200mV below ground to within 1.5V of the positive supply rail. The MAX9107/MAX9108/MAX9109 outputs are TTL-compatible, requiring no external pullup circuitry. These easy-to-use comparators incorporate internal hysteresis to ensure clean output switching even when the devices are driven by a slow-moving input signal. The MAX9107/MAX9108/MAX9109 are higher-speed, lower-power, lower-cost upgrades to industry-standard comparators MAX907/MAX908/MAX909. The MAX9109 features an output latch but does not have complementary outputs. The dual MAX9107 is available in both 8-pin SO and SOT23 packages. The quad MAX9108 is available in TSSOP and SO packages.
MAXIM MAX9647/MAX9648 Manual
The MAX9647/MAX9648 comparators are general-purpose, low-voltage, tiny pack comparators with advantages of low supply voltage, small package, and low cost. They also offer a wide supply voltage range, wide operating temperature range, competitive CMRR and PSRR, response time characteristics, input offset, low noise, output saturation voltage, input bias current, and RF immunity.
MAXIM MAX4480 MAX4483 Manual
MAX4480-MAX4483 Series Single/Dual/Quad Low Power Operational Amplifiers
MAXIM MAX9636/MAX9637/MAX9638 Manual
The MAX9636/MAX9637/MAX9638 are single-supply, CMOS input op amps featuring wide bandwidth at low quiescent current, making them suitable for a broad range of battery-powered applications such as portable medical instruments, portable media players, and smoke detectors.
MAXIM MAX4238/MAX4239 Manual
MAX4238/MAX4239 are low-noise, low-drift, ultra- high precision amplifiers that offer near-zero DC offset and drift through the use of patented autocorrelating zeroing techniques. This method constantly measures and compensates the input offset, eliminating drift over time and temperature and the effect of 1/f noise. Both devices feature rail-to-rail outputs, operate from a single 2.7V to 5.5V supply, and consume only 600µA. An active- low shutdown mode decreases supply current to 0.1µA. The MAX4238 is unity-gain stable with a gain-band- width product of 1MHz, while the decompensated MAX4239 is stable with AV ≥ 10V/V and a GBWP of 6.5MHz. The MAX4238/MAX4239 are available in 8-pin narrow SO, 6-pin TDFN and SOT23 packages.
MAXIM MAX9943/MAX9944 Manual
The MAX9943/MAX9944 family of high-voltage amplifiers offers precision, low drift, and low-power consumption
MAXIM MAX9617 MAX9620 Manual
MAX9617-MAX9620 is a low-power, zero-drift operational amplifier with 1.5MHz GBW and 10µV zero-drift input offset voltage. The device is available in SC70 package and suitable for portable consumer, medical and industrial applications.
MAXIM MAX9613/MAX9615 Manual
The MAX9613/MAX9615 are low-power precision op amps with rail-to-rail inputs and rail-to-rail outputs. They feature precision MOS inputs powered from an internal charge pump to eliminate crossover distortion that is common to complementary input-pair type amplifier architectures. These devices are ideal for a large number of signal pro- cessing applications such as photodiode transimped- ance amplifiers and filtering/amplification of a wide variety of signals in industrial equipment.