ANALOG Manuals

ADG1236 is a dual SPDT switch from Analog Devices. It features low capacitance, low charge injection, and a wide supply voltage range. The device is manufactured using iCMOS process and has good anti-interference ability.

ADG1211/ADG1212/ADG1213 are low-power, low-capacitance, low-charge injection ICMOS quad SPST switches with ±15V/+12V operating voltage range, featuring 1pF switch off capacitance, 2.6pF switch on capacitance, <1pC switch charge injection, 33V supply range, 120Ω switch on resistance, 3V logic compatible input, no VL supply requirement, support Rail-to-Rail operation, with 16-lead TSSOP and 16-lead LFCSP packages.

ADG1208/ADG1209 are low capacitance, 4/8 channel ±15 V/+12 V iCMOS™ multiplexers

The ADG1206 and ADG1207 are monolithic iCMOS analog multiplexers comprising sixteen single channels and eight differential channels, respectively. These devices feature extremely low switch capacitance and switch resistance and are suitable for a wide variety of applications including audio and video routing, automatic test equipment, data acquisition systems, battery-powered systems, sample-and-hold systems, and communication systems.

The ADG1204 is a 4:1 CMOS multiplexer fabricated in the iCMOS process. It features a 2 pF switch offset capacitance and 1 pC switch charge injection, a supply voltage range of 33 V, fully specified at +12 V and ±15 V, no VL supply required, 3 V logic-compatible inputs, a 120 ohm on resistance, and rail-to-rail operation.

The ADN8831 is a monolithic controller that drives a Thermoelectric Cooler (TEC) to stabilize the temperature of a laser diode or a passive component used in telecommunications equipment. This device relies on a Negative Temperature Coefficient (NTC) thermistor or a positive temperature coefficient RTD device to sense the temperature of the object attached to the TEC. The target temperature is set with an analog input voltage either from a DAC or with an external resistor divider. The loop is stabilized by a PID compensation amplifier with high stability and low noise.

ADN8830 is a thermoelectric cooler controller with features of high efficiency, small size, low noise, etc. It is suitable for applications such as thermoelectric cooler temperature control, resistive heating element control, temperature stabilization, etc.

ADN8820 is a programmable laser driver and controller in the ADN series with four operating modes: constant laser current, constant optical output power, constant EDFA gain and constant laser power. High power efficiency: >90%

The ADN8810 is a 12-bit programmable high output current source with high precision, low noise, long term stability, current output from 0 mA to 300 mA, output fault indication, low drift, programmable maximum current, 24-lead 4 mm × 4 mm leadframe chip scale package and 3-wire serial interface.

This datasheet provides a comprehensive overview of the ADN2892's features, including input sensitivity, 70ps rise/fall times, CML outputs, bandwidth, LOS output, programmable LOS detector, Rx signal strength indicator (RSSI), SFF-8472 compliant average power measurement, single-supply operation, low power dissipation, and compact 16-lead LFCSP package.

The ADN2890 is a 3.3V 2.7Gb/s limiting amplifier that provides high gain, limiting amplification for SONET, Gigabit Ethernet (GbE), and Fibre Channel optical receivers that accept input levels of up to 2.0V p-p differential and have 3mV p-p differential input sensitivity.

The ADN2882 is a compact, high performance 3.3 V power supply SiGe transimpedance amplifier (TIA) optimized for small form factor 4.25Gbps optical modules compliant with SFF-8472 receivers, PIN/APD-TIA receive optical subassembly, SONET/GbE/FC optical receivers, transceivers, and transponders.

The ADN2882 is a 3.3 V low noise transimpedance amplifier with a bandwidth of 3.5 GHz, input noise current density of 8 pA/√Hz, optical sensitivity of -22.0 dBm, differential transimpedance of 3700 V/A, power dissipation of 80 mW, differential output swing of 260 mV p-p, input overload current of 5.6 mA p-p, on-chip RSSI function, low frequency cutoff of 12 kHz, and die size of 0.7 mm × 1.2 mm.

The ADN2880 is a 3.3 V, low noise transimpedance amplifier (TIA) with a bandwidth of 2.5 GHz, optical sensitivity of -24.2 dBm, differential transimpedance of 4400 V/A, power dissipation of 70 mW, and differential output swing of 260 mV p-p. It is suitable for optical receivers with a data rate of 3.2 Gbps or below, and can be used in SONET/GbE/FC optical receivers and SFF-8472 compliant receivers. It is also compatible with PIN/APD-TIA receive optical subassemblies (ROSA).