ANALOG Manuals

The AD600/AD602 are dual channel, low noise, wideband variable gain amplifiers optimized for use in ultrasound imaging systems but are applicable to any application requiring precise gain, low noise and high bandwidth.

AD8033/AD8034 are low-cost, 80 MHz FastFET™ op amps with features such as FET input, high speed, low noise, wide supply voltage range, and low power consumption.

The AD8031/AD8032 are Analog Devices' low power, high speed, full range input output amplifiers with 800uA current and 80MHz bandwidth.

AD8029/AD8030/AD8040 is a low power, high speed, rail-to-rail input/output amplifier. It features low power consumption, high speed, rail-to-rail input/output, etc.

AD8027/AD8028 is a low distortion, high speed rail-to-rail input/output amplifier. It features a high speed 190 MHz bandwidth, 100 V/µs slew rate, low distortion of 120 dBc @ 1 MHz SFDR, low noise of 4.3 nV/√Hz, low offset voltage of 900 µV max, etc. It is suitable for applications such as filters, ADC drivers, level shifting, buffering, professional video, low voltage instrumentation, etc.

AD8026 is a low cost, closed loop, voltage feedback, quad amplifier. Precision trimmed resistors set a fixed RF/RG ratio of 5/3 to a typical gain accuracy of 0.02%

The AD8024 is a low settling time, high-speed, high output voltage quad current feedback operational amplifier. It is manufactured on ADI’s proprietary high gain low noise process and features high output drive capability and low power consumption. The AD8024 is ideal for LCD column drivers, high performance test equipment, video line drivers and ATE applications.

The AD8023 is a high current output drive, high voltage output drive, triple video amplifier. Each amplifier has 70 mA of output current and is optimized for driving large capacitive loads. The amplifiers are current feedback amplifiers and feature gain flatness of 0.1 dB to 10 MHz while offering differential gain and phase error of 0.06% and 0.02°.

AD8021 is a very high performance, high speed voltage feedback amplifier that can be used in 16-bit resolution ADC preamp and driver, instrumentation preamp, active filters, portable instrumentation, line receivers, precision instruments, ultrasound signal processing and high gain circuits.

The AD8019 is a low-cost xDSL line driver optimized to deliver a minimum of 13 dBm of output power into a 100 Ω load while providing outstanding distortion performance.

The AD8018 is a 5V, rail-to-rail, high-output current xDSL line drive amplifier. It is an ideal amplifier for USB, PCMCIA, or PCI-based customer premise equipment (CPE). The AD8018 provides maximum reach on a 5V supply, driving 16 dBm of power into a back-terminated, transformer-coupled 100-ohm load while maintaining -82 dBc of out-of-band SFDR. The amplifier features rail-to-rail output voltage and high output current drive, with the ability to drive 400 mA of output current into a differential load of 10 ohms at 8V p-p. It has low single-tone distortion of -86 dBc worst harmonic at 6V p-p into a differential 10-ohm load at 100 kHz. The AD8018 also has low noise, low power operation, high speed, and current feedback amplifiers.

The AD8017 is a low cost, dual high speed amplifier capable of driving low distortion signals to within 1.0 V of the supply rail. It is intended for use in single supply xDSL systems where low distortion and low cost are essential. The amplifiers will be able to drive a 50 Ohm load with 20 V p-p differential output or a 25 Ohm load with 10 V p-p single ended output.

The AD8016 is a high output current xDSL line driver from Analog Devices. It features low power, high output current and high speed. The device supports -5V to -12V power supply, works with less than 50mA of current, and can provide up to 24.4dBm of output power for ADSL, HDSL2 and proprietary xDSL systems.

AD8015 is a wideband/differential output transimpedance amplifier launched by Analog Devices, with low cost, wide bandwidth, and low noise.